Router setup in Canberra, placed well and locked down
A new router still in its box, a modem your provider just posted, or an old one that's never been touched since the NBN went in. We set it up where it actually reaches, lock down the settings that are left open from the factory, and add guest Wi-Fi and parental controls that work. Visits across Canberra and nearby NSW, 7 days a week.
Call 1300 224 027 or use the form. Tell us your router model, your NBN connection type and what plugs into the old modem.
Connect and place it
We connect the router with your provider's settings, test the signal in the rooms you use and settle on the best spot.
Lock it down and set up networks
Admin password, security mode, firmware, guest and smart-home networks, then parental controls if you want them.
Move your devices and show you
Your devices are reconnected and tested, and we show you how to pause the internet, add a guest and check for updates in the app.
Before and after
Drag the handle to compare. The same kind of job, photographed on the bench before and after.
BeforeAfter
Under-desk cables, tidied Cables run, tied and off the floor.
Wi-Fi in every room
Where mesh nodes go in a typical Canberra home.
RouterMoved out of the cupboard where possible.
Mesh nodesOne per floor or zone, ideally wired back.Drawn in red: where we focus first
Brick and foilThe walls that block signal in older homes.
Outdoor reachGranny flats, studios and the backyard.
Where the router goes matters most
Wi-Fi weakens with every wall, far more through brick, tiles and foil-backed insulation. We measure the signal in the rooms you use and pick the spot from the numbers.
The ideal spot
Central, at chest height or higher, and out in the open. A router at one end of the house leaves far bedrooms with scraps.
The usual bad spots
Wherever the NBN cable ends: a hallway cupboard, behind the TV, under a desk, or the garage.
If the router can’t move, a cable from the NBN box to a better spot often can, using data points many newer homes have. Too many walls? You need mesh Wi-Fi, not a stronger router.
What a proper router setup includes
Plugging a router in takes two minutes. The work is in the settings nobody changes and the problems that show up a week later.
Placement tested first
We measure the signal where you actually sit before the router is fixed in place, and move it if the numbers say so.
One router, not two
The provider's modem goes into bridge mode, or your new router into access point mode, so only one device does the routing.
Admin access locked
A new admin password, remote management off, and WPS switched off so the router can't be joined by guessing a PIN.
WPA3 where it works
WPA3 for devices that support it, with WPA2 kept for older printers and smart plugs on a network of their own.
Current firmware
Updated on the day, with automatic updates turned on so security fixes keep arriving after we leave.
Guest Wi-Fi with a QR code
Visitors get internet and nothing else, joined by scanning a code instead of reading out your password.
A smart-home network
Plugs, cameras and appliances on their own 2.4 GHz network, kept apart from the laptops with your banking on them.
Family profiles that hold
A profile for each child with a bedtime pause, backed up by controls on the devices themselves.
Devices moved across
Where it makes sense we reuse your old Wi-Fi name and password, so most devices rejoin without being touched.
Provider modem, your own router, or both
The router moved out of a closed cabinet to an open, high shelf, with the signal tested before the cables were clipped.
The provider’s modem plus your own router, both handing out addresses, means double NAT. Browsing works, so nobody notices until a console can’t join a party chat or a work VPN drops.
Only one device should do the routing
Modem in bridge mode
Your router takes over. Choose this for mesh family features: many mesh systems turn off parental controls and some security features in access point mode.
Router in access point mode
The provider’s modem stays in charge. Needed when your provider only delivers the home phone through its own modem’s phone port.
NBN connection
What you need
Fibre to the node or building
A VDSL2 modem router on the phone socket
Fibre to the premises or curb, fixed wireless, cable (HFC)
A router with a WAN port; the NBN box or connection device is the modem
Most router complaints come down to a handful of causes. Here's how we read them on site.
What you noticeLikely causeThe fix
What you noticeStrong signal near the router, weak in the bedroomsLikely causeRouter in the garage, a cupboard or behind the TVThe fixMove it to an open, central spot, or add a mesh node
What you noticeConsole says Strict NAT, NAT Type 3 or Double NATLikely causeProvider modem and your router both routingThe fixBridge mode on the modem, or access point mode on the router
What you noticeSmart plug or camera won't join the new networkLikely cause2.4 GHz-only device meeting a combined or WPA3-only networkThe fixA separate 2.4 GHz network on WPA2 for smart devices
What you noticeOlder laptop or printer can't see the Wi-FiLikely causeNetwork set to WPA3 only, or 6 GHz onlyThe fixWPA2/WPA3 mixed mode on 2.4 and 5 GHz
What you noticeHome phone went dead after the router swapLikely causeThe phone service ran through the old modem's phone portThe fixEnter your provider's VoIP details, or keep the old modem as the modem
What you noticeWi-Fi drops on hot afternoonsLikely causeRouter overheating in a hot garage or closed cabinetThe fixMove it somewhere ventilated and out of the sun
What you noticeKids' bedtime schedule stopped workingLikely causePhone using a rotating private Wi-Fi addressThe fixSet the address to Fixed for home Wi-Fi, and add device controls
What you noticeCan't log in to the routerLikely causeAdmin password changed years ago and forgottenThe fixFactory reset, then set it up again from scratch
Not sure which one it is? Send us the symptoms and we’ll tell you before you travel.
The security settings we change every time
A typical before: an old router on the carpet under a desk, with power boards and cables piled around it.
Routers leave the factory set up to be easy, not safe. We change these every time; the Australian Cyber Security Centre’s guidance at cyber.gov.au covers the same ground.
Change the admin password and turn off remote management, so settings can’t be reached from the internet.
Turn off WPS. Its PIN can be brute-forced on many routers, and joined devices don’t need it.
Set the security mode on purpose. WPA3 where devices support it, WPA2 with AES for older ones, never WEP or WPA with TKIP.
Update the firmware and switch on automatic updates. If your model no longer gets updates, we’ll tell you to replace it.
Decide on UPnP. It lets games and apps open ports automatically: on for gaming households, off where nothing needs it.
Provider's modem, your own router or a mesh system?
All three can run a home network. Which suits you depends on the house more than the brand.
Swipe to compare
Provider's modem router
Your own router
Our pickMesh system
Upfront cost
Often included with the plan
Low to mid
Mid to high
Covers a single-storey brick veneer home
Partial
Partial
Covers double brick or two storeys
Firmware updates
Pushed by the provider
Yes, with auto-update on
Yes, automatic on most
Keeps a provider home phone working
Only with a phone port
Rarely, so keep the modem
Guest and smart-home networks
Basic
Parental controls
Basic or none
Varies by brand
Yes, some by subscription
Best for
Small units close to the NBN box
Compact homes and gamers who like settings
Most family homes
Where the provider's modem carries your home phone, we often keep it as the modem and let your own router or mesh run the Wi-Fi.
Guest and smart-home networks
Router and NBN box tidied in a hallway nook, with the provider's modem retired.
Visitors and smart devices each get their own network, kept apart from your computers and phones.
Guest network
Internet and nothing else. With isolation on, guests can’t see your computers, printer or cameras, and you can change the password between short-stay visitors. Most router apps show a QR code for guests to join.
Smart-home network
Many plugs, bulbs and doorbells only work on 2.4 GHz with WPA2, and won’t join a combined or WPA3 network. Cheap devices rarely get security updates, so keep them off your banking laptop’s network.
If it has an app or a web admin page, we can set it up. These are the ranges sold most widely in Australia.
Mesh systems
TP-Link Deco
Netgear Orbi
Google Nest Wifi Pro
ASUS ZenWiFi
Linksys Velop
Standalone routers
TP-Link Archer
Netgear Nighthawk
ASUS RT and ROG Rapture
Ubiquiti UniFi Express and Dream Router
Wi-Fi 7
TP-Link Deco BE series
TP-Link Archer BE series
Netgear Orbi 770 and 970
ASUS ZenWiFi BT8 and BT10
VDSL2 modem routers (node and building)
TP-Link Archer VR series
ASUS DSL-AX82U
The modem router your provider sent
Satellite and mobile
Starlink Gen 3 router and Router Mini
4G and 5G home modems
Newest gear
Released in the last few months: ask us about your model
Parental controls that actually hold
Router controls set a profile per child, group their devices and pause the internet at bedtime, including on TVs and consoles with weak controls of their own.
Some brands include content filtering free and others charge monthly. Cloudflare’s family DNS, 1.1.1.3, adds a basic adult-content filter to every device at no cost.
Router controls never see mobile data, VPN apps or friends’ Wi-Fi, so we pair them with device controls for app approvals, purchases and limits anywhere.
Device
Built-in controls
iPhone and iPad
Screen Time, under Settings > Screen Time
Android
Google Family Link
Windows and Xbox
Microsoft Family Safety
Parental controls: router, device or both?
Router controls cover everything on your Wi-Fi. Device controls follow the child out the door. Most families need both.
Swipe to compare
Router controls
Device controls (Screen Time, Family Link)
Our pickBoth together
Covers every device on the home Wi-Fi
Works on mobile data and at friends' houses
One-tap pause for the whole house
App approvals and purchase limits
Covers TVs and consoles without their own controls
Hard for a teenager to step around
Partial
Partial
Harder, not impossible
Ongoing cost
Free on most, some filters by subscription
Free
Free to low
Our view
Good for younger children
Essential once they have a phone
Best for most families
Consoles have their own family settings too: Microsoft Family Safety for Xbox, PlayStation family management and the Nintendo Switch Parental Controls app.
When a new router isn't the answer
A new router can’t speed up a slow plan or fix an NBN line fault. So we first test the speed at the NBN box with a cable.
Slow at the box
It’s the line or the plan. We’ll help you take it up with your provider or look at TechBox Internet.
Fast at the box, slow in the bedrooms
It’s coverage, fixed by better placement or a mesh system.
Packages
Starting points we tailor to your property. Every package is quoted after a quick look.
Router swap
Units, townhouses and smaller homes replacing a provider modem or an old router
Connected to your NBN box or phone socket with your provider's settings
Placement checked with a signal test in the main rooms
Admin password changed, WPS and remote admin off
WPA3 or WPA2 security set to suit your devices
Firmware updated and automatic updates switched on
Ten minutes of preparation means the visit goes on settings, not hunting for passwords.
Stop and call us if: If the NBN box shows a red Alarm light, or no lights even though its power point is on, the problem is on the NBN side, so call your provider first. If a router or its power pack is hot to touch or smells of burning, unplug it at the wall.
Real Google reviews. We ask every customer, every time.
Duvi came out to fix my computer today and I'm so very happy to say that it is now working again! I'm so grateful as Duvi saved me thousands of dollars because a major electronics chain told me i needed a new computer.
Maree W., Google review
Prompt, professional, and very helpful. Highly recommend.
CHRISTINE F., Google review
Duvi was great. Identified and resolved the problem with our computer quickly, and arranged the necessary repairs. Delighted with the outcome.
Not always. A provider modem is often fine in a small home close to the NBN box. It's worth replacing or adding to when coverage is poor, it lacks the controls you want, or it no longer gets updates. If it carries your home phone, we usually keep it as the modem and let your own router or mesh run the Wi-Fi.
Where should the router go?
As central as the cabling allows, up off the floor and out in the open. Cupboards, the back of the TV unit, metal meter boxes, fish tanks and mirrors all cost signal, and the microwave interferes with 2.4 GHz. If the NBN box is in the garage, network cabling or a mesh system gets the Wi-Fi to the middle of the house.
Should I use WPA3?
Yes, for every device that supports it. WPA3 resists the offline password guessing that weakens WPA2, and it's required on the 6 GHz band. Many printers, smart plugs and older laptops only support WPA2, so we keep WPA2 available for them on a separate network rather than weakening the main one.
Will all my devices need reconnecting?
Often not. If we give the new router the same Wi-Fi name and password as the old one, most phones, TVs and printers rejoin by themselves. The exceptions are devices that can't handle the new security mode, which we move to the smart-home network.
What is double NAT and why does my console care?
It happens when two routers sit in a row, each translating addresses. Browsing works, but online games, voice chat and some video calls struggle to connect, which consoles report as Strict NAT, NAT Type 3 or Double NAT detected. Putting one of the two devices into bridge or access point mode fixes it.
Can router parental controls work on mobile data?
No. Router controls only see devices on your home Wi-Fi. Once a phone switches to mobile data or joins a friend's Wi-Fi, only controls on the device itself apply, such as Screen Time on an iPhone or Google Family Link on Android. That's why we set up both.
Does a guest network keep visitors away from my computers?
Yes, when guest isolation is switched on, which we check. Guests get internet access but can't see your computers, printer or cameras. The trade-off is that guests can't cast to your TV from the guest network, so we'll set it up the way your household uses it.
How long does a router setup take and what does it cost?
A straightforward swap is often done within the first hour, and on-site visits are $189 for the first hour, then billed in 30-minute blocks. Parental controls for several children, lots of smart devices or a mesh system take longer, and we'll give you an idea of time when you book.