Repairs
Business IT
Starlink
Home
Call 1300 224 027Book a repair

Open 7 days, 9 am to 8 pm

Starlink and internet

Starlink installation guide for the Canberra region

A practical guide to installing Starlink on properties around Canberra, from choosing between the Standard and Mini kits to checking gums and deciduous trees through the seasons, choosing a mount, running and sealing the cable, powering it and getting Wi-Fi to every room and shed.

  • 5 min read
Open 7 days, 9 am to 8 pm
“Prompt, professional, and very helpful. Highly recommend.”
CHRISTINE F., Google review
A Starlink dish on a low stand on the metal roof of a weatherboard farmhouse, looking out over golden paddocks, gum trees, a dam and blue hills in early morning light

Key takeaways

  • Run the Starlink app's obstruction check from where the dish will actually sit, not from the lawn.
  • A deciduous tree that looks clear in July can block the dish by December, and gums keep growing.
  • Fasten mounts into rafters, purlins, studs or a concreted pole, never into fascia boards or roof sheeting alone.
  • Choose the router position and the cable route together, so the Wi-Fi starts near the middle of the house.

Install problems we're called out to fix

Most Starlink trouble on rural properties traces back to one of these. Each one is avoidable on install day.

What you noticeLikely causeThe fix
What you noticeVideo calls freeze every few minutesLikely causeA branch or roofline in the dish's viewThe fixCheck the obstruction map, then move or raise the dish
What you noticeFine all winter, drops out from NovemberLikely causeDeciduous tree now in full leafThe fixRe-check in leaf, then prune or relocate
What you noticeDish leaning after a strong westerlyLikely causeMount fixed to a fascia board or gutterThe fixRe-mount into rafters, purlins or a pole
What you noticeWater stain near the cable entryLikely causeNo drip loop, or an unsealed holeThe fixDrip loop plus a grommet or flashed entry
What you noticeDrips around the roof mountLikely causeScrews through the valley of the sheetThe fixRe-fix through the crest with sealing washers
What you noticeWeak Wi-Fi at the far end of the houseLikely causeRouter left wherever the cable reachedThe fixMove the router, or add wired mesh nodes
What you noticeDrops out when a window is closedLikely causeCable crushed in the window frameThe fixRe-route through a proper sealed wall entry
What you noticeReboots in storms and short blackoutsLikely causePower dips with no backupThe fixA UPS sized for the kit, plus surge protection

Not sure which one it is? Send us the symptoms and we’ll tell you before you travel.

Rather we call you?

Leave your number. We call back 9 am to 8 pm, 7 days, to talk through your roof and the cable run.

We only use your number to call you about this.

the dish's field of view, which has to stay clear of trees and roofs
110°
of cable in the Standard box, the first limit on where the dish goes
15 m
Standard kit's average draw on Starlink's spec sheet. Mini: 25-40 W
75-100 W
longest single network cable run if the router moves out to a shed
100 m

Start with the sky, not the kit

Anyone can switch Starlink on, but a permanent install has to survive Canberra’s frosts, spring westerlies and summer storms for years while the trees around it grow.

The dish hands over between moving satellites constantly, so one branch in view causes a drop each time a satellite passes behind it. Video calls freeze; browsing barely notices.

  1. Scan from dish height. Run the app’s obstruction check at the ridge, pole top or wall bracket. Can’t safely get up? An upstairs window beats the lawn.
  2. Compare two or three spots. One end of a roof can be clear while the other drops out every few minutes.
  3. Borderline results? A Starlink site survey checks every spot at dish height; our obstruction guide helps an existing install.

Trees and seasons around Canberra

Trees cause more Starlink problems here than anything else, and what you see depends on when you look.

  • Summer: the worst case

    Deciduous trees in full leaf and the most storms. If the dish is clear in January, it's probably clear all year.

  • Autumn: leaves dropping

    Oaks, elms, poplars and fruit trees thin out, which can hide a problem that comes back in spring.

  • Winter: misleadingly clear

    Bare branches make a survey look better than summer will. Picture every tree in full leaf, and allow for frost and snow on high ground.

  • Spring: growth and wind

    Rapid new growth and the windiest weather of the year. Check the view and the mount once the westerlies settle.

  • Gums keep growing

    Eucalypts keep their leaves but put on height fast and drop limbs. Plan for the tree in five years, not today.

  • Pines block it all

    Farm windbreaks are dense all year. Mount clear of them rather than hoping the dish will see through.

Choose the right kit

For homes and farms the choice is the Standard kit or the Mini, and the difference that matters most is where the router lives.

  • Standard kit

    The router sits indoors on one cable carrying power and data, so it can go near the middle of the house, which matters most for good Wi-Fi. Right for almost every permanent home, farm or business.

  • Mini

    Its Wi-Fi is built into the dish, so indoor coverage depends on how close the dish is to the rooms you use. The 12 to 48 V DC input suits utes, caravans, solar sheds and backup.

See Starlink Mini setup and caravan setup. Older dishes, such as the earlier motorised model, follow the same principles with different routers, cables and mounts.

Standard or Mini for a fixed property?

Both kits use the same satellites. For a home, the difference is where the router lives and how much power it needs.

Swipe to compare

Our pickStandard kitMini kit
Router indoors, near the middle of the houseNo, it's built into the dish
Average power draw75-100 W25-40 W
Runs straight from 12 V DCYes, 12 to 48 V
Wi-Fi coverage from the kit aloneUp to 297 m²Up to 112 m²
Wired portsTwo on the routerOne, with Starlink's Mini cable
Cable in the box15 m Starlink cable15 m DC power cable
Best forHomes, farms and businessesSheds, weekenders, utes and backup

Figures from Starlink's published specifications at the time of writing. Starlink updates its hardware, so check the current sheet before you buy.

Choose a mount and fix it properly

Trialling a candidate spot on a temporary stand. The dish's own obstruction map shows whether it sees enough sky before anything is fixed down.
Trialling a candidate spot on a temporary stand. The dish's own obstruction map shows whether it sees enough sky before anything is fixed down.

When trees are tall and close, moving the dish away usually beats raising it. Starlink rates the Standard dish operational in winds of 96 km/h and above; it’s rarely the dish that fails, but the mount and what it’s fixed to.

Whatever the mount, fix it into structure, not cladding. A 20 m gum 10 m from the house still fills a big slice of sky from the ridge, while a pole 25 m from the same tree may see over it. Most houses suit a Starlink roof mount; treed blocks suit a Starlink pole mount in a concrete footing, cable buried in conduit.

  • Metal roofs. Screw through the crest, never the valley, into the purlin or rafter, with sealing washers. Sweep off drill swarf, which rusts into the sheet.
  • Tiled roofs. Lift the tiles, fix to a rafter and refit them to shed water. Brittle or steep tiles often suit a wall or pole mount better.
  • Brick and weatherboard. Masonry anchors into solid brick, not mortar joints; on weatherboard, fix into the studs.

Ground stands are for testing only: as a permanent home they leave the dish within reach of dogs, stock and mowers. Starlink relocation re-mounts a badly fixed dish properly, including when you move.

Plan the cable, router and power together

A ridge mount lifts the dish above nearby gums, with the cable entering under the ridge cap.
A ridge mount lifts the dish above nearby gums, with the cable entering under the ridge cap.

Treat the cable route and router position as one decision, so the cable arrives near the middle of the house. Measure the whole route before you commit to a dish spot.

Starlink sells a longer cable than the one in the box. Its plugs are larger than network plugs, so size entry holes to suit, and never cut and re-join it: that creates a weak point and may affect your warranty.

  • Drip loops below every entry, so water drips off
  • Sealed entries: a grommet, weatherproof wall plate or flashed roof entry
  • UV-stable conduit or tight clips, against rubbing and cockatoos
  • Underground runs in conduit, clear of irrigation, route marked
  • Beyond cable reach, the router moves to a powered shed or enclosure
  • Network cable then runs up to 100 m; fibre or point-to-point goes further

Which mount suits your property?

The best spot for the sky isn't always the best spot for the building. These are the trade-offs we weigh on site.

Swipe to compare

Roof or ridgeWall bracketPole or mastGround stand
Gets above nearby treesPartial
No holes in the roof
Out of reach of stock, dogs and mowersPartial, fence it
Fixed intoRafters or purlinsStuds or solid brickA concrete footingIts own kickstand or base
Main risk if done badlyLeaks at screws or ridge cappingFixings pulling out of claddingUndersized footing, loose guysKnocked over, chewed cable
SuitsMost houses with a clear roof faceGable ends facing open skyTreed blocks, dish away from the houseTesting and temporary use

When tall trees sit close to the house, moving the dish away from them often does more than raising it.

Get Wi-Fi to every room and shed

One central router may suit a compact home, but rural homes are often long, double brick or spread out, with a granny flat or shed too.

  • Starlink mesh units

    Starlink’s own mesh units extend the network from its router and set up in the app.

  • Bypass mode

    Hands the network to your own mesh or wired access points, for better guest networks, a smart-device network and outdoor coverage.

  • Network cable

    Cable to a home office, smart TV or mesh node gives the most stable connection.

  • Outbuildings

    Close sheds can take a mesh node at a window facing the house; further away, use buried cable or a point-to-point link. Corrugated iron blocks Wi-Fi almost completely, so the access point goes inside.

Activate, test and look after it

Activate the kit in the app, let it settle for a few hours, then test before you rely on it.

  1. Check the obstruction map. It’s built from the dish’s own data, so it beats the camera check.
  2. Test from the rooms you use. Not beside the router: make a video call where you work.
  3. Test mid-morning and evening. Speeds vary with demand in your area.
  4. Check the outage history. After a few days, regular short drops usually point to an obstruction.

Then check the mount from the ground after big storms, review trees yearly and prune before spring growth. Check exposed cable for UV damage and chewing, and rinse a caked dish with water, never a pressure washer or solvent. On solar, review the snow-melt setting before winter.

DIY or a professional install?

Plenty of people install Starlink themselves. Here's where DIY stops making sense.

Swipe to compare

DIYProfessional install
Sky check from the real mount heightOnly where you can safely reach
Fixed into rafters, purlins or a footingPartial: depends on tools and roof
Sealed entries with drip loopsPartial
Router placed for whole-house Wi-FiPartial: limited by the cable route
Wi-Fi to sheds and cottagesPartial
CostYour time and partsA quote before any work starts
SuitsOpen block, wall or ground mount, short cableRoofs, poles, trees, long runs and sheds

Roof work is the riskiest part of any install. If you're not comfortable on a ladder or a roof, don't go up.

Common questions

Still stuck? Call 1300 224 027, 9 am to 8 pm, 7 days.

How long does a Starlink installation take?

It depends on the mount and the cable run. A ground or wall setup with a short cable is quick, while a roof or pole mount with concealed cable, sealed entries and mesh Wi-Fi takes considerably longer. A new pole may also need its concrete footing to cure before the dish goes up.

Can I install Starlink myself?

Yes, if you have a clear spot that's easy and safe to reach, the cable reaches the router without drilling through roofs or walls, and a simple mount will do. For roof work, two-storey homes, poles, long cable runs or Wi-Fi to outbuildings, a professional install is usually worth it.

Which way should the dish face?

Follow the Starlink app. It guides you through aiming the dish when you set it up and tells you if it needs adjusting. What you control is where the dish sits, and the obstruction check tells you whether that spot can see enough sky.

Does Starlink work in heavy rain?

Mostly, yes. Very heavy rain, hail and thunderstorms can slow the connection or cause short dropouts while the storm is overhead, and it recovers as the storm passes. Steady, light rain rarely makes a noticeable difference.

Will growing trees affect my connection later?

Yes. Gums grow quickly and deciduous trees fill in every spring, so a spot that's clear now may not be in a few years. Check the obstruction map in the app once a year, and again after a big spring flush of growth.

Do I need a UPS for Starlink?

If short blackouts are common at your property, or you work from home, a UPS sized for the kit's power draw is worth having. It keeps the router and dish running through short outages and smooths out power spikes during storms.

Can I move the dish later?

Yes. Moving it around the same property is simply a reinstall in a new spot, and the obstruction check tells you whether the new spot works. If you move house, update your service address with Starlink, because residential plans are tied to an address.

Reviews from TechBox customers

Real Google reviews.

The service I have received from TechBox has been nothing but amazing!! I haven’t seen such service for years.I had a problem and asked for their help , from the beginning to the end they were tenacious working through the issues I had with my software. Thank you so much for your help TechBox. You people are most professional I will have no problem…

Steve W., Google review

Very quick. Very efficient. Excellent value for money.

Keith J., Google review

Great friendly service, on time to solve the problem

Bruce W., Google review

Get a mount plan and a fixed quote

Tell us about the property. We plan the mount, the cable run and the Wi-Fi so it works in every room and every season.

1300 224 027

Calls answered 9 am to 8 pm, 7 days.

  • Quote before any work starts
  • Workshop in Mitchell, visits across Canberra
  • If something isn’t right, we come back and make it right.
“Very quick. Very efficient. Excellent value for money.”
Keith J., Google review

Get a Starlink install quote

Tell us about the property. We’ll check the site and quote the mount and cable run.

Starlink quoteTB-·····

Property type
Do you have a kit?

What happens next

  1. We call you back, 9 am to 8 pm, 7 days.
  2. We talk through the roof, trees and cable run, then confirm the mount and a price.
  3. We book the visit. Nothing is ordered until you say yes.

Open 7 days, 9 am to 8 pm
Prefer to talk? Call 1300 224 027. We only use your details to answer this request.

Open 7 days, 9 am to 8 pm

Call nowBook online