Repairs
Business IT
Starlink
Home
Call 1300 224 027Book a repair

Open 7 days, 9 am to 8 pm

Starlink and internet

Mesh Wi-Fi guide: whole-home Wi-Fi that reaches every room

Why Wi-Fi drops out in some rooms and how to get a strong signal everywhere: mesh systems, extenders and wired access points compared, why backhaul matters, where to put nodes, which Wi-Fi standard to buy, and how to set up security, guest networks and smart-home devices.

  • 5 min read
Open 7 days, 9 am to 8 pm
“Great friendly service, on time to solve the problem”
Bruce W., Google review
Three small white mesh Wi-Fi nodes of the same set placed on a timber table, with their power cables coiled and a short Ethernet cable

Key takeaways

  • Dead zones are usually caused by distance and building materials, not by the internet plan.
  • Mesh systems beat extenders because the nodes work as one network and hand your devices between them.
  • Wired backhaul is the single biggest improvement you can make to a mesh system.
  • Place each node roughly halfway between the last one and the dead zone, up off the floor and out in the open.

Why is the Wi-Fi bad in that room?

Where and when it's slow usually points straight at the cause.

What you noticeLikely causeThe fix
What you noticeSlow everywhere, even on a cableLikely causeThe NBN connection or the planThe fixCheck the connection and plan; mesh won't help
What you noticeFast by the router, slow at the far endLikely causeDistance and wallsThe fixA mesh node halfway, not in the dead zone
What you noticeMesh added, far rooms still slowLikely causeShared backhaul through too many hopsThe fixWire one node, or move nodes closer together
What you noticeApp rates one node's link as weak or fairLikely causeNode too far from the one before itThe fixMove it closer, or wire its backhaul
What you noticeSmart plug won't pairLikely cause2.4 GHz-only device, bands sharing one nameThe fixA separate 2.4 GHz network for smart devices
What you noticeFine inside, nothing on the deckLikely causeBrick, foil or Low-E glass in the wayThe fixAn outdoor-rated node under the eaves
What you noticeGame lag, console reports strict NATLikely causeTwo routers in a row (double NAT)The fixModem in bridge mode, or mesh in access point mode
What you noticeGranny flat gets nothingLikely causeSeparate building, too many wallsThe fixA buried cable or a point-to-point link

Not sure which one it is? Send us the symptoms and we’ll tell you before you travel.

Rather we call you?

Leave your number. We call back 9 am to 8 pm, 7 days, to talk through your roof and the cable run.

We only use your number to call you about this.

signal strength that keeps video calls smooth
-67 dBm
the three standard 2.4 GHz channels that don't overlap
1, 6, 11
longest Ethernet cable run for wired backhaul to a node
100 m
on-site visit, first hour, then 30-minute blocks
$189

Why some rooms have no Wi-Fi

Wi-Fi is radio, and it weakens with distance and with every wall, floor and appliance it passes through. By the far bedroom there may not be much left.

  • Light

    Plasterboard walls, timber floors and doors, and ordinary glass.

  • Moderate

    Brick veneer, a single internal brick wall, and wardrobes full of clothes.

  • Heavy

    Double brick, concrete slabs, stone, foil sarking and insulation, metal cladding, Low-E glazing, mirrors, fish tanks and the fridge.

Security settings worth five minutes

Most of these are a toggle in the router or mesh app. The ACSC's cyber.gov.au has plain-English advice on securing a home network.

  • Use WPA3

    Or WPA2/WPA3 mixed mode if older devices can't join. Avoid the old WEP and WPA settings entirely.

  • A long passphrase

    Four or five random words: easier to type and far harder to guess than a short, complicated password.

  • Lock down the admin

    Change the router's admin password, and turn on two-step sign-in for the mesh app account if it's offered.

  • Turn off WPS

    The push-button and PIN pairing feature has a long history of security weaknesses.

  • Automatic firmware updates

    Most mesh systems can update themselves overnight. Turn it on and leave it on.

  • Remote management off

    Unless you genuinely need it, don't expose the router's settings page to the internet.

  • A guest network

    Visitors get online without your main password, and without a view of your computers, printers or cameras.

  • A smart-device network

    A separate 2.4 GHz network for plugs, bulbs and cameras keeps them apart from your laptops and phones.

  • Retire unsupported routers

    A router that no longer gets firmware updates is a weak point for every device in the house.

Bands and Wi-Fi standards

Good whole-home Wi-Fi uses all three bands. A good Wi-Fi 6 mesh with wired backhaul will outperform a Wi-Fi 7 system with nodes in the wrong places.

Band Best for Trade-off
2.4 GHz Range through walls, smart devices Slower; crowded by neighbours (fiercely in apartments), microwaves, baby monitors and Bluetooth; only channels 1, 6 and 11 don’t overlap
5 GHz Everyday speed Shorter range through walls
6 GHz (Wi-Fi 6E and 7) Same-room devices and links between nodes Shortest range

Wi-Fi 6, the sensible minimum for a new system, copes with a busy household far better than Wi-Fi 5. Its Target Wake Time helps battery life on phones and smart devices.

Extender, powerline, mesh or wired access points

Four ways to get Wi-Fi to the far end of the house, and what each really delivers.

Swipe to compare

ExtenderPowerlineOur pickMesh systemWired access points
One network name across the housePartialPartial
Hands devices between rooms smoothly
Speed at the far endAbout half, often lessVaries with the wiringGood, best with wired backhaulClose to full
Copes with double brick and slabsPartialPartial
Works without new cabling
Easy to add coverage laterPartialPartial
Relative costLowestLowMidHighest, with cabling
Best forA quick fix for one roomA room Wi-Fi can't reach, after testingMost homes, brick veneer, two storeysDouble brick, large homes, cabled builds

A mesh system with even one wired node closes most of the gap with ceiling access points.

Extenders, mesh and backhaul

The NBN connection box often lives in the garage. Where it sits decides where the main node starts.
The NBN connection box often lives in the garage. Where it sits decides where the main node starts.

The comparison on this page can’t show why extenders disappoint, or that backhaul decides how fast far rooms really are.

  • Extenders. Most resend on the same radio, roughly halving the speed, and many create a second network name devices cling to.
  • Mesh. Nodes act as one network, steering each device to the strongest node. Buy every node from one range.
  • Powerline. Uses your electrical wiring and can reach a room without new cabling, but with older wiring, several circuits or noisy appliances it’s slow and drops out. Test one first.
  • Dual-band backhaul. The same radios carry devices and the link back, so speed drops each hop, which frustrates beyond two nodes.
  • Wired backhaul. The biggest single improvement, and some newer homes already have data points. One cable to the far node usually lifts speeds close to those beside the router.

Where to put the router and nodes

A node can only pass on what it receives, so put each one where its link back is still strong.

  • Start with the router

    The main node connects to the NBN box or modem, in many Canberra homes in the garage or a hallway cupboard. If cabling reaches a central room, move it there. NBN connection setup and router setup visits cover this.

  • Halfway, not in the dead zone

    In a dead zone a node rebroadcasts a weak signal. Place it roughly halfway, and trust the app’s placement test over a hunch.

  • Up and in the open

    On a shelf, not under a desk, in cupboards or behind TVs, and clear of mirrors, fish tanks, microwaves and metal. Stagger nodes through a floor or stairwell on two storeys.

  • Outdoor areas

    Rather than hoping signal escapes through brick and Low-E glass, use an outdoor-rated node or access point under the eaves, out of rain and direct sun.

Backhaul options compared

Backhaul is how each node talks back to the router. It decides how fast the far rooms really are.

Swipe to compare

Our pickWired (Ethernet)Dedicated wirelessShared wireless
Found onAny mesh system with Ethernet portsTri-band and quad-band systemsDual-band systems
Keeps full speed at each nodePartial
Node radios left free for your devices
Works without a cable to the node
Good for three or more nodesPartial
Copes with double brick between nodesPartial
Best forAny home with a data point or a cable pathBrick veneer, nodes a room or two apartSmall homes with two nodes

Most mesh systems accept a mix: wired where a cable exists, wireless for the rest.

Canberra homes: what to watch for

A router moved out of a cabinet onto a high, open shelf: free, and often the first improvement we make.
A router moved out of a cabinet onto a high, open shelf: free, and often the first improvement we make.

Each type of Canberra home has its own Wi-Fi problem.

  • Double brick. Older inner north and inner south homes need a node in each wing, ideally wired.
  • Brick veneer. Most suburbs from the 1960s onwards, often with foil that blocks signal to the garage and yard.
  • Split levels. Concrete between levels blocks far more than timber, so plan nodes level by level.
  • New builds. Gungahlin, Molonglo and other new estates: foil insulation, metal roofs and Low-E glazing trap Wi-Fi indoors.
  • Acreage and long single-storey homes. Distance is the enemy and wired backhaul pays off; on Starlink, see Starlink Wi-Fi extension.
  • Granny flats and studios. A node at a facing window, a buried cable or a short point-to-point wireless link.

Guest and smart-home networks

Two details make the guest and smart-device networks in the security settings work.

  • Guest and rental networks

    Many apps share the guest password as a QR code, and you can change it without reconnecting everything. Give a granny flat or short-stay rental its own network, so you can change its password between stays without affecting visitors.

  • Smart devices

    Many cheap plugs, bulbs, cameras and robot vacuums rarely get security updates, the real reason to keep them off your main network. Matter over Thread devices use a border router, usually a smart speaker or hub, which needs a solid connection.

Planning from scratch? See smart home installation. Cameras need steady Wi-Fi or, better, a cable: see CCTV installation.

Wi-Fi 6, 6E or 7?

A newer standard only helps devices that support it, and only up to your plan speed for anything from the internet.

Swipe to compare

Wi-Fi 6Wi-Fi 6EWi-Fi 7
Bands2.4 and 5 GHz2.4, 5 and 6 GHz2.4, 5 and 6 GHz
Widest channel160 MHz160 MHz320 MHz, on 6 GHz
Multi-Link Operation
Phones and laptops that support itMost made since 2020Many made since 2022Flagships from 2024 on
6 GHz available for backhaul
Relative priceLowestMidHighest
Best forMost homes on a typical NBN planBusy homes with newer devicesFast plans, new devices, wired backhaul

Good node placement and wired backhaul matter more than the standard printed on the box.

Testing it, and when to call us

Test it the way you use it.

  1. Wired test. Speed test at the router to see what the connection delivers.
  2. Walk the house. Speed test every room you use, outdoors included.
  3. Check signal. Stronger than about -67 dBm suits video calls; below about -70 dBm, calls suffer.
  4. Call and walk. Walk around on a video call to check your device changes nodes cleanly.
  5. Retest in the evening. That’s when the household and your neighbours are online.

Get help for double brick, split levels, backhaul cabling, granny flats, outdoor areas, or dead zones a new mesh didn’t fix. A visit is $189 for the first hour, then billed in 30-minute blocks.

Common questions

Still stuck? Call 1300 224 027, 9 am to 8 pm, 7 days.

Is mesh Wi-Fi better than a Wi-Fi extender?

In almost every home, yes. An extender repeats the signal, often halving the speed and creating a second network your devices have to switch between. A mesh system's nodes work together as one network, manage the links between them and hand your devices over as you move around.

How many mesh nodes do I need?

It depends more on the walls than the floor area. A compact brick veneer home may need two nodes, while a double-brick home or a long single-storey house can need three or four. Start with the problem rooms and the construction, and add nodes only where testing shows a gap.

Should I turn off the Wi-Fi on my provider's modem?

Usually, yes, if a mesh system is taking over. Two sets of Wi-Fi in the same house compete for channels, and two routers in a row can cause problems with gaming and video calls. Ideally, put the provider's modem in bridge mode, or set the mesh system to run in access point mode.

Does mesh Wi-Fi work with Starlink?

Yes. You can add Starlink's own mesh units to the Starlink router, or put the Starlink router into bypass mode and connect a mesh system of your choice. Bypass mode gives you more control over guest networks and smart-home devices.

Why won't my smart plug connect?

Many smart-home devices only work on 2.4 GHz and get confused when 2.4 and 5 GHz share one network name. Setting up a separate 2.4 GHz network for smart devices usually solves it, and it keeps those devices apart from your computers.

Is WPA3 worth turning on?

Yes, where your devices allow it. WPA3 protects your Wi-Fi password far better against guessing attacks. If some older devices can't connect, use the router's WPA2/WPA3 mixed mode, or put the older devices on their own network.

Can I mix different brands of mesh nodes?

Generally, no. There is an industry standard for mixing brands, but compatibility is patchy, and the management features usually only work within one brand. Buy all your nodes from the same range.

Reviews from TechBox customers

Real Google reviews.

Prompt, professional, and very helpful. Highly recommend.

CHRISTINE F., Google review

Duvi was great. Identified and resolved the problem with our computer quickly, and arranged the necessary repairs. Delighted with the outcome.

ruth d., Google review

Excellent professional service- very prompt home visit, quick diagnosis of my computer problem and then it was fixed and returned to my house next day. I will certainly use this company again.

ironbark v., Google review

Get a mount plan and a fixed quote

Tell us about the property. We plan the mount, the cable run and the Wi-Fi so it works in every room and every season.

1300 224 027

Calls answered 9 am to 8 pm, 7 days.

  • Quote before any work starts
  • Workshop in Mitchell, visits across Canberra
  • If something isn’t right, we come back and make it right.
“Very quick. Very efficient. Excellent value for money.”
Keith J., Google review

Get a Starlink install quote

Tell us about the property. We’ll check the site and quote the mount and cable run.

Starlink quoteTB-·····

Property type
Do you have a kit?

What happens next

  1. We call you back, 9 am to 8 pm, 7 days.
  2. We talk through the roof, trees and cable run, then confirm the mount and a price.
  3. We book the visit. Nothing is ordered until you say yes.

Open 7 days, 9 am to 8 pm
Prefer to talk? Call 1300 224 027. We only use your details to answer this request.

Open 7 days, 9 am to 8 pm

Call nowBook online