Repairs
Business IT
Starlink
Home
Call 1300 224 027Book a repair

Open 7 days, 9 am to 8 pm

Console HDMI port repair in Canberra for no signal and flickering

The console powers on but the TV says no signal, the picture flickers or the port feels loose. We replace damaged HDMI ports on PS5, PS4, Xbox Series X and S and Xbox One consoles, and repair the HDMI chip beside the port when that's the fault. You get a fixed quote before any work starts.

“Very quick. Very efficient. Excellent value for money.”
Keith J., Google review
  • Open 7 days, 9 am to 8 pm
  • 90-day warranty
  • Quote before work
  • We rule out the TV and cable first
  • PS5, PS4, Xbox Series X and S, Xbox One
  • Micro-soldering under the microscope
  • Tested at full resolution before you collect it
  • Open 7 days, calls until 8 pm
A new HDMI port being soldered onto a games console circuit board under a magnifier lamp
HDMI port
Confirmed before we start
Turnaround
1 to 3 business days for most consoles
Where
Mitchell workshop, open 7 days
Warranty
90 days, parts and labour

Rather we call you?

Leave your number. A technician calls back 9 am to 8 pm, 7 days, with a price range for your model.

We only use your number to call you about this.

in a standard HDMI port, on one thin plastic tongue
19 pins
for most port replacements, including testing
1-3 days
a fixed price once the port and chip are measured
Quote first
warranty on parts and labour
90 days

HDMI faults we fix

  • No signal, but the console powers on

    The light comes on and the controller connects, but the TV shows nothing. Usually the port or the HDMI chip behind it.

  • Flickering or the picture dropping out

    Often a cracked solder joint or a loose port, though cables and soundbars can cause it too. We test which.

  • Works only with the cable held at an angle

    A classic sign of a port that has started to lift from the board. Stop wiggling it, because each movement tears the pads further.

  • Bent, broken or missing pins

    Look into the port with a torch. Pins pushed flat, a cracked plastic tongue or a crooked port all mean a replacement.

  • Port loose or pushed into the console

    A port that moves when you plug in the cable has broken away from its mounting. It needs to be removed and properly soldered back in.

  • Lower resolution only, or no 4K at 120 Hz

    A marginal connection can pass a basic picture but fail at full bandwidth. A faulty cable can do the same, so we test both.

  • No picture after a storm or power surge

    A surge through the cable or power can damage the HDMI chip on the board. A new port alone won't fix that, so we test before quoting.

  • A repair someone has already attempted

    Torn pads and heat damage are common after a home repair. It's often still fixable with pad repair and jumper wires.

  • Switch dock shows nothing on the TV

    The dock's port, the dock's board or the Switch's own USB-C port. We test the console and dock separately.

Pick the job. We confirm a fixed price for your exact model before any work starts.

What happens next

  1. Check the TV and cable

    Run through the checks on this page first. If it's still dead, call 1300 224 027 or start a repair ticket online, and bring the console and its HDMI cable.

  2. We inspect and test

    We inspect the port under the microscope, test with a known-good TV and cable, and measure the signal lines to the HDMI chip before we quote.

  3. We repair it

    The old port comes off with hot air and flux, the pads are cleaned or rebuilt, and a new port is soldered on and inspected under magnification.

  4. Tested at full resolution

    We test at the highest resolution and refresh rate your console can output, with HDR, while flexing the cable. If something isn't right afterwards, we make it right.

Exploded technical drawing: inside a home console

Inside a home console

Heat, ports and power: the usual suspects.

  • Cooling fanDust and wear cause noise, heat and shutdowns.Drawn in red: the part we replace most
  • Heat sinkCleaned and re-pasted. Some use liquid metal.
  • HDMI portBent pins and lifted ports need micro-soldering.
  • Power supplyDead consoles and clicking starts.
  • Disc driveWon’t read, won’t eject, or grinds.

How HDMI ports get damaged

Hot air and flux release the old port without lifting the pads beneath it.
Hot air and flux release the old port without lifting the pads beneath it.

A standard HDMI port has 19 contacts on a thin plastic tongue inside a metal shell. It’s built for thousands of plug-ins, but not sideways force.

Most damage comes from a cable pulled at an angle: the console moved to vacuum, knocked off a shelf, tripped over by a dog or a toddler, or carried off with the cable still in.

  • Bent or flattened pins, often in the middle of the row
  • A cracked tongue, which leaves the pins nothing to sit on
  • Cracked solder joints, causing flicker and an intermittent picture
  • A port lifting off the board, tearing the copper pads underneath

What you get with an HDMI repair

Most of the work is in proving where the fault is, then soldering a tiny part without damaging the board around it.

  • Known-good TV and cable

    Every no-signal console goes on our own TV and cable first, so you don't pay for a port you don't need.

  • Inspected under magnification

    Pins, tongue, solder joints and pads are checked under the microscope before we quote.

  • Signal lines measured

    Each line between the port and the HDMI chip is measured, so we know if it's the port, the chip or both.

  • Low-melt solder removal

    The old port releases with hot air, flux and low-melt solder, so the pads underneath survive.

  • Anchored, not just tacked

    Signal pins first, then the shell legs that take the strain when a cable gets tugged.

  • Full bandwidth test

    Highest resolution and refresh rate the console supports, HDR on, with the cable gently flexed.

  • Games and saves untouched

    A port repair doesn't touch storage, and testing the picture doesn't need your account password.

  • 90-day warranty

    Parts and labour are covered. If something isn't right afterwards, we make it right.

When it isn't the port: the HDMI chip

Every pin and pad is inspected under the microscope before and after soldering.
Every pin and pad is inspected under the microscope before and after soldering.

A small chip between the processor and the port converts or cleans up the video signal. When it fails there’s no picture, however perfect the port looks, and a new port alone won’t fix it.

Repairers usually call it the HDMI encoder on PlayStation consoles and the retimer on Xbox Series consoles. It can be damaged by:

  • A surge through the cable or the power point, which is why summer storms matter
  • Static discharge or liquid
  • A short from a damaged port, such as a bent pin touching the shell
  • Heat from a rough repair attempt

We measure each signal line between the port and the chip before quoting, so you know whether you need a port, a chip or both. A failed chip comes off with hot air, and every joint on the new one is inspected under the microscope.

Is it the port, the chip or the TV?

Where the picture fails, and what changes it, usually points to the cause. This is how we read it on the bench.

What you noticeLikely causeThe fix
What you noticeConsole starts, no signal on every TVLikely causeDamaged port or a failed HDMI chipThe fixPort inspected and signal lines measured, then quoted
What you noticePicture only with the cable held at an angleLikely causePort lifting or cracked solder jointsThe fixStop wiggling it; port reflowed or replaced
What you noticeFlicker or sparkles at 4K 120 Hz onlyLikely causeCable bandwidth, or a marginal jointThe fixUltra High Speed cable test, then a port check
What you noticeWorks into the TV, not through the soundbarLikely causeSoundbar or receiver can't pass the signalThe fixConsole into the TV, sound out through eARC
What you noticeBent, flattened or missing pinsLikely causeCable forced in or pulled sidewaysThe fixNew port. Straightened pins rarely last
What you noticeNo picture after a stormLikely causeSurge damage to the HDMI chipThe fixChip replaced. A port alone won't fix it
What you noticePicture in Safe Mode, black after restartLikely causeA resolution or HDR setting the TV rejectsThe fixLower the video settings. No repair needed
What you noticeSwitch works in handheld, not on the TVLikely causeDock port, dock board or the USB-C portThe fixConsole and dock tested separately

Not sure which one it is? Send us the symptoms and we’ll tell you before you travel.

What the repair involves

The new port is soldered signal pins first, then the shell legs that anchor it.
The new port is soldered signal pins first, then the shell legs that anchor it.

HDMI pads are small enough to tear if the old port is forced off. So it comes off with hot air, flux and fresh low-melt solder, without overheating the board or nearby parts.

Torn pads or broken traces are rebuilt with fine jumper wire. The new port is soldered signal pins first, then the shell legs that take the strain, and every joint is checked and each line measured again.

We then test at the highest resolution and refresh rate your console supports, with HDR on, while gently flexing the cable, and run an extended session before we call you.

Port, chip or pads: which repair do you need?

Three different faults that all end in a black TV. We measure before quoting so you only pay for the one you have.

Swipe to compare

Port replacementChip replacementPad and trace rebuild
Fixes bent, broken or loose pinsYes, with a new port
Fixes flicker from cracked jointsYes, with a new port
Fixes no picture after a surgeRarelyRarely
Fixes a failed earlier attemptPartial
Games and saves kept
Typical time1 to 3 business daysQuoted after testingQuoted after inspection
Relative costLowestHigherMid to higher

Some consoles need a port and a chip together, especially after a surge or a bent pin touching the shell.

What moves the price and the time

We quote after measuring, and these decide the price and the time.

  • Port, chip or both

    A clean port replacement costs least. A failed chip adds a part and bench time, and torn pads or traces need rebuilding before a new port goes on.

  • Your console and its revision

    PS5 and Series X ports are HDMI 2.1 parts, and boards differ between revisions, so we match the part to yours.

  • Earlier attempts

    Excess solder, lifted pads and heat damage take time to put right, so tell us if someone has already tried.

  • Parts

    Common ports are easy to get. Some chips are ordered in, and we give you the date when we quote.

Consoles we repair HDMI and video faults on

Ports for current consoles are usually easy to source. For anything rare or imported, tell us the model number when you book.

PlayStation

  • PS5, all original revisions
  • PS5 Digital Edition
  • PS5 Slim
  • PS5 Pro
  • PS4, PS4 Slim and PS4 Pro

Xbox

  • Xbox Series X
  • Xbox Series S
  • Xbox One
  • Xbox One S
  • Xbox One X

Nintendo

  • Switch (2017 and 2019)
  • Switch OLED
  • Original and OLED docks
  • Switch 2 and its dock: ask us

No TV output by design

  • Switch Lite

Nintendo Switch: video through USB-C

The Switch has no HDMI port of its own. It sends video through its USB-C port to the dock, which converts it to HDMI for the TV.

With no picture, the fault can be

  • The dock’s HDMI port or its own board
  • The console’s USB-C port
  • A chip behind it, such as the M92T36 USB-C power-delivery chip

A dock or charger that doesn’t follow the USB-C standard can kill the M92T36. We test in handheld mode and with a known-good dock to split those apart, and Nintendo Switch repairs covers the rest.

HDMI on each console

Newer consoles push far more data through the same-shaped port, which is why a marginal repair shows up at 4K and not at 1080p.

Swipe to compare

PS5 familyXbox Series X|SPS4 familyXbox One family
HDMI version2.12.11.4; 2.0 on PS4 Pro1.4; 2.0 on One S and One X
4K at 120 HzSeries X only
Chip behind the portHDMI encoderHDMI retimerHDMI encoderVaries by model
Other HDMI socketsNoneNoneNoneHDMI in on most models
Cable for full outputUltra High SpeedUltra High SpeedHigh Speed; Premium on PS4 ProHigh Speed; Premium on One S and X
Low-resolution startSafe Mode: Change Video OutputXbox + Eject to the second beepSafe Mode: Change ResolutionXbox + Eject to the second beep

On an Xbox One, the cable to the TV must go into HDMI out. On a Series S or One S All-Digital, use Pair in place of Eject for a low-resolution start.

Preventing it, and whether it's worth it

A port replacement is almost always worth it on a PS5, Xbox Series console or PS4, and a chip usually is on a current console.

If a surge damaged more of the board, we’ll weigh the cost against its value honestly.

  • Leave slack, so a tug pulls the cable, not the port
  • Unplug the HDMI cable before moving the console, every time
  • Avoid heavy cables and adapters that hang off the port
  • Share one surge-protected board with the TV, and unplug both in big storms
  • Fix a wobbly vertical stand, or lay the console flat

Not sure it's the port?

Bring the console and its cable to our Mitchell workshop, or book a repair online.

Rule these out first

Ten minutes of checks solves a surprising number of no-signal consoles. If none of them helps, you'll know it's worth booking in.

Stop and call us if: If the port moves, the pins are bent or the picture only appears with the cable held at an angle, stop plugging it in. Every wiggle tears the pads further and adds to the repair.

What Canberra customers say

Real Google reviews. We ask every customer, every time.

Tech Box saved the day!!!!!!!!!!! With my laptop on the brink of despair, I turned to Tech Box for help, and they delivered beyond expectations. Their expert team swiftly diagnosed and resolved the issue, displaying a level of professionalism that's truly commendable.

Gihani W., Google review

Very personable and professional attention to the problem. Would use again.

Paula K., Google review

The service I have received from TechBox has been nothing but amazing!! I haven’t seen such service for years.I had a problem and asked for their help , from the beginning to the end they were tenacious working through the issues I had with my software. Thank you so much for your help TechBox. You people are most professional I will have no problem…

Steve W., Google review

Questions about console HDMI ports

Straight answers. More in our questions and answers.

Still deciding?

Call a Canberra technician, 9 am to 8 pm, 7 days.

Call 1300 224 027
How do I know if it's the HDMI port or my TV?

Try a different HDMI input, a different cable and another device on the same input. If everything else shows a picture and the console doesn't, on any TV or cable, the fault is in the console. A look into the port with a torch often confirms it.

Can a bent HDMI pin just be straightened?

Sometimes, if it's only slightly bent, but the pins are tiny and brittle, and a straightened pin often fails again. A pin pushed flat or snapped needs a new port. Please don't try it with a needle at home, because a pin touching the metal shell can short the HDMI chip.

What is the HDMI encoder or retimer chip?

It's a small chip between the console's processor and the HDMI port that converts or cleans up the video signal for your TV. It can fail after a power surge or a short from a damaged port. When it fails, a new port alone won't bring the picture back.

How long does an HDMI port repair take?

Most port replacements take 1 to 3 business days, including testing. A chip replacement or pad repair can take longer, depending on the part, and we'll tell you the expected time when we quote.

Someone else tried to fix my port. Can you still repair it?

Often, yes. Torn pads and broken traces can be rebuilt with fine jumper wires under the microscope. Tell us what was done, and we'll inspect it before quoting.

Will I lose my games or saves?

No. An HDMI repair doesn't touch the console's storage, so your games, saves and settings stay where they are.

Can you fix a Nintendo Switch that won't show on the TV?

Yes. The Switch sends video through its USB-C port to the dock, so the fault can be the dock, its HDMI port or the console's USB-C port. The Switch Lite doesn't connect to a TV at all, by design.

How do I stop it happening again?

Leave slack in the cable, never move the console with the cable plugged in, and avoid heavy cables or adapters that hang off the port. Plug the console and TV into the same surge-protected power board.

Get it booked in today

Call now, or send a ticket and we’ll call you back with a time and a price range. Drop it at Mitchell or we come to you.

1300 224 027

Calls answered 9 am to 8 pm, 7 days.

  • Quote before any work starts
  • Workshop in Mitchell, visits across Canberra
  • If something isn’t right, we come back and make it right.
“Great friendly service, on time to solve the problem”
Bruce W., Google review

Start a repair ticket

Tell us what’s wrong. We’ll call you back with a time and a price range.

Repair ticketTB-·····

What needs fixing?

What happens next

  1. A technician calls you back, 9 am to 8 pm, 7 days. Sent after 8 pm? We call from 9 am.
  2. You get a price range and a time for your model.
  3. Nothing starts until you say yes.

Open 7 days, 9 am to 8 pm
Prefer to talk? Call 1300 224 027. We only use your details to answer this request.

Open 7 days, 9 am to 8 pm

Call nowBook online