Repairs
Business IT
Starlink
Home
Call 1300 224 027Book a repair

Open 7 days, 9 am to 8 pm

Office network cabling in Canberra, planned by us and installed by registered cablers

New desks, ceiling access points, cameras or a whole new tenancy. We plan the cabling around how you'll use the space and coordinate a registered cabler to install and test every run. Then we patch, label and configure the network ourselves, so you have one plan and one contact from start to finish.

“Duvi was great. Identified and resolved the problem with our computer quickly, and arranged the necessary repairs. Delighted with the outcome.”
ruth d., Google review
  • Open 7 days, 9 am to 8 pm
  • Free IT review
  • Cabling planned around desks, access points and cameras
  • Installed and tested by registered cablers
  • Cat6 to desks, Cat6A where speed and PoE need it
  • Labelled at both ends, with a port map handed over
  • Asbestos registers and landlord approvals checked first
Close-up of a patch panel being terminated with blue Cat6 cables neatly dressed and cable-tied, a punch-down tool resting on top
IT review
Free
Turnaround
Scoped on site, then scheduled around your trading hours
Where
On-site across Canberra and nearby NSW

Talk to us about your IT

Leave your number. We call back during opening hours to book your free IT review, or just to answer questions.

We only use your number to call you about this.

the longest copper Ethernet channel, patch leads included
100 m
carries 10 Gb/s to 100 m. Cat6 manages it to about 55 m
Cat6A
the Wiring Rules that registered cablers install to
AS/CA S009
the cabling advice form your cabler gives you when the job is done
TCA1

Cabling jobs we plan and manage

  • A new tenancy or refit

    Desks, meeting rooms, printers, access points and cameras planned from the floor plan before the ceiling closes.

  • More desks than data points

    Desk switches daisy-chained under tables and cables taped along the carpet to reach the printer.

  • Access points with nowhere to plug in

    Each ceiling access point needs its own run, and higher-end Wi-Fi 7 models have 5 or 10 Gb/s ports and draw more PoE power.

  • A comms cupboard nobody wants to open

    Unlabelled cables, long patch leads in a knot and equipment sitting on the floor with no UPS.

  • Points that are dead or slow

    Desks stuck at 100 Mb/s, wall plates that don't work and connections that come and go.

  • Cameras around the building

    PoE runs to CCTV positions in warehouses, car parks and entrances, kept on their own network.

  • A shed, workshop or second building

    Fibre in conduit between buildings, instead of copper that picks up surges in a storm.

  • Moving out at the end of a lease

    Make-good clauses that mention cabling, worked through with the cabler and your landlord before the final inspection.

What happens next

  1. Walk the site

    We look at the space, the comms cupboard, ceiling access and cable paths, and how you plan to use each room.

  2. Design and quote

    You get a floor plan with every outlet and access point, the cable type for each run, the cabinet details and a quote before work starts.

  3. Cabler installs and tests

    A registered cabler runs, terminates and tests every cable, ideally before ceilings close on a fit-out, and gives you the TCA1 form.

  4. Patch, configure and hand over

    We patch and label, set up switches and Wi-Fi, test every desk and hand over the documentation.

Before and after

Drag the handle to compare. The same kind of job, photographed on the bench before and after.

After: comms cupboard, sortedBeforeAfter
Comms cupboard, sorted From tangle to dressed, tied and documented.
Exploded technical drawing: a small business network

A small business network

The cupboard that keeps the office running.

  • Patch panelEvery desk cable terminated and labelled.
  • SwitchPower for access points and phones, separated networks.
  • FirewallFilters traffic, runs the VPN and gets updates.Drawn in red: where we focus first
  • UPSRides through short outages and shuts down cleanly.

What structured cabling actually is

Structured cabling means every outlet has its own cable running back to one place. Any desk can then move to any port in seconds, and a fault affects one point instead of half the office.

  1. Wall plate or ceiling point. Each outlet gets its own cable in the wall, the permanent link, up to 90 metres long.
  2. Patch panel. That cable ends at a numbered port on a patch panel in the comms cabinet.
  3. Patch lead to the switch. A short lead links the port to the switch, with 10 metres in total for leads at both ends.

The alternative in many growing offices is a desk switch, a second one daisy-chained off it and a cable taped along the skirting. It works until a cleaner unplugs the wrong thing.

A small office network with cabling running back to one cabinet
Each desk and ceiling access point has its own run back to the patch panel, where short leads connect it to the switch and firewall.

What a properly cabled office includes

Good cabling disappears into the walls and outlasts several generations of computers and Wi-Fi. These are the parts that make that happen.

  • Designed from your floor plan

    Every outlet, access point and camera position marked, with spare points where furniture is likely to move.

  • Registered cablers only

    All fixed cabling is installed by registered cablers working to the Wiring Rules, never by a handyman.

  • The right cable for each run

    Cat6 to desks and printers, Cat6A to access points and between cabinets, fibre between buildings.

  • Every run tested

    Each run is tested with a cable analyser, and you keep the report alongside the TCA1 form.

  • Labelled at both ends

    The wall plate and the patch panel port carry the same ID, so desk 14 is port 14 without any tracing.

  • A cabinet that makes sense

    Patch panels, short leads, switch, firewall and NBN equipment mounted in order, with space left to grow.

  • Power and cooling planned

    A UPS for the network gear and ventilation for a cupboard that bakes in a Canberra summer.

  • Patched and configured

    We connect the switches and access points and set up the separate networks, so it all works on day one.

  • Documentation handed over

    Floor plan with outlet IDs, port map and test results, kept current if you're on a managed plan.

Who is allowed to do the work

Cat6 runs dressed into the back of the patch panel, ready to be terminated and tested.
Cat6 runs dressed into the back of the patch panel, ready to be terminated and tested.

In Australia, cabling fixed in walls, ceilings, floors or conduit must be installed by a cabler registered under the ACMA’s Cabling Provider Rules.

  • The registered cabler

    Runs the cable, fits wall plates, terminates the patch panel and tests it, following AS/CA S009, the Wiring Rules, on things like separation from power and cable support.

  • The TCA1 form

    The cabling advice the cabler gives you, recording the work and confirming it meets the rules.

  • TechBox

    We plan and manage the job, then patch, label, connect and configure the network side, from the switches to the ceiling access points.

What's wrong with my office cabling?

Cabling faults look like network faults. Here's how we tell them apart on site.

What you noticeLikely causeThe fix
What you noticeDesk connects at 100 Mb/s, not 1 Gb/sLikely causeOne of the four pairs broken or badly terminatedThe fixRe-terminate and retest the run
What you noticeWall point completely deadLikely causeNot patched at the panel, or the cable is damagedThe fixTrace it with a toner, then patch or re-run it
What you noticeAccess point keeps rebootingLikely causeSwitch PoE budget exceeded, or a faulty patch leadThe fixCheck PoE draw per port and replace the lead
What you noticeRandom dropouts across several desksLikely causeCopper-clad aluminium cable or untwisted terminationsThe fixReplace non-compliant runs with solid copper Cat6
What you noticeShed or second building drops out in stormsLikely causeCopper link between buildings picking up surgesThe fixReplace it with fibre in conduit
What you noticeOne side of the office is slowLikely causeDesk switches daisy-chained off a single cableThe fixHome runs from each desk back to the patch panel
What you noticeNobody knows which port is whichLikely causeNo labels and no port mapThe fixTrace, label both ends and document every port

Not sure which one it is? Send us the symptoms and we’ll tell you before you travel.

Planning outlets, access points and spare capacity

Before: unlabelled cables, a router on the floor and nothing on a UPS.
Before: unlabelled cables, a router on the floor and nothing on a UPS.

Most cabling mistakes are planning mistakes, and they’re expensive to fix once ceilings are closed and furniture is in.

  • two outlets per desk, so a dock and a phone don’t need a desk switch
  • a Cat6A run for each ceiling access point, placed from a Wi-Fi survey
  • points for meeting room screens and video bars, printers, TVs and reception
  • camera positions for business CCTV, on their own network
  • spare runs to likely future spots, with draw wires left in the conduit

Access points, cameras and desk phones draw power through the cable, so the switch needs enough PoE budget, and big PoE bundles run warm in a ceiling, one reason we use Cat6A for access points.

Cat5e, Cat6 or Cat6A

Older Canberra offices often have Cat5e in the walls. Here's what each category can carry and where we use it.

Swipe to compare

Cat5eCat6Our pickCat6A
Rated bandwidth100 MHz250 MHz500 MHz
1 Gb/s to 100 m
2.5 Gb/s for Wi-Fi 6E and 7 access pointsYes, in most cases
5 Gb/s to 100 mPartial
10 Gb/s to 100 mUp to about 55 m
Heat headroom for high-power PoE in big bundlesLeastGoodBest
Cable sizeAbout 5 mmAbout 6 mmAbout 7 to 8 mm, needs more tray space
Installed costLowest, rarely used newMidHighest
Where we use itExisting runs that test wellDesks, printers, phones and camerasAccess points, uplinks and long-life fit-outs

Cable is the cheap part of a cabling job. Labour, ceiling access and making good cost more, so upgrading a run you're already pulling to Cat6A is often worth it.

Older buildings, strata and new estates

After: patch panel, short leads, switch and firewall mounted in order, every port labelled.
After: patch panel, short leads, switch and firewall mounted in order, every port labelled.

Canberra’s office buildings bring their own challenges, and each kind of site changes the plan.

Site What it means for cabling
1970s and 1980s blocks in Woden, Belconnen and Civic Concrete slabs, shallow ceiling voids and shared risers. Many predate 2004, so the asbestos register decides where the cabler can drill
Heritage-listed buildings and some strata complexes Extra approval steps, so we start those conversations early
Light-industrial sites in Mitchell, Fyshwick and Hume Long runs, high ceilings and paths past roller doors and forklifts. Points beyond 90 metres need a second switch location, linked by fibre
New builds and fit-outs in Gungahlin and Molonglo Easy, if we’re in before the plasterboard. Cabling at frame stage costs much less than retrofitting

Bring us in when the electrical plan is drawn. If you’re moving, office IT setup and relocation runs the whole project and the office move IT checklist covers the timing.

Who does what on a cabling job

Australian rules decide who can work on the cabling in your walls. This is how the work splits.

Swipe to compare

You or your staffTechBoxRegistered cabler
Decide where desks, screens and cameras goPartial
Design outlet, access point and cabinet layoutPartial
Run cable in walls, ceilings and floors
Terminate wall plates and the patch panel
Test every run and issue the TCA1 form
Plug in pre-made patch leads
Set up switches, firewall and Wi-FiMounting only
Keep the port map and documentation currentPartial

Anyone can plug a pre-made lead into a wall plate or a switch. Anything fixed in place is a registered cabler's job by law.

A comms cupboard the next person can understand

The cabinet is where the cabling meets the network, and where most of the mess ends up.

  • Sized to grow. A wall-mounted cabinet for a small office, or a floor-standing rack when there’s a server or a lot of patching.
  • Easy to read. Patch panels and switches mounted alternately, with short leads in a colour scheme agreed with you.
  • Labelled and documented. Every outlet carries its patch panel port ID, and the floor plan, port map and test results go into your network documentation.
  • Powered and cooled. Firewall, switches and NBN equipment on a UPS, with ventilation checked, because PoE switches in a closed cupboard get very hot in a Canberra January.

The switches, separate networks and firewall are configured in the same job, so the cabling works on day one. After that, moves and additions sit under managed IT services, or we come back as you need us.

Packages

Starting points we tailor to your property. Every package is quoted after a quick look.

Comms cupboard tidy-up

Offices whose cabling works, but whose cupboard is a tangle

  • Existing runs traced and tested before anything moves
  • Equipment mounted in a wall or floor cabinet
  • Short colour-coded patch leads in place of the knot
  • Switch, firewall and NBN equipment on a UPS
  • Every port labelled and a port map handed over
  • A registered cabler booked if any runs need re-terminating
Get this quoted

Extra points or access points

A new room, more desks or ceiling Wi-Fi in an existing office

  • Site check of the cabinet, ceiling space and cable paths
  • Outlet and access point positions marked on a floor plan
  • Registered cabler runs and terminates Cat6 or Cat6A
  • Test report and TCA1 form for the new runs
  • Switch ports, PoE and separate networks configured
  • Port map and documentation updated
Get this quoted

New fit-out or office move

A new tenancy, a refit or a relocation

  • Cabling design from the fit-out drawings
  • Coordination with the builder, electrician and landlord
  • Cabinet size, UPS and ventilation planned
  • Every run installed and tested by a registered cabler
  • Network ready and tested before staff arrive
  • Full handover documentation
Get this quoted

Before you book a cabling job

A little preparation keeps the quote accurate and saves a second visit.

Stop and call us if: Don't run, join or terminate cable in walls or ceilings yourself, and don't let a handyman do it. Fixed cabling must be installed by a registered cabler.

What Canberra customers say

Real Google reviews. We ask every customer, every time.

Very quick. Very efficient. Excellent value for money.

Keith J., Google review

The service I have received from TechBox has been nothing but amazing!! I haven’t seen such service for years.I had a problem and asked for their help , from the beginning to the end they were tenacious working through the issues I had with my software. Thank you so much for your help TechBox. You people are most professional I will have no problem…

Steve W., Google review

Duvi was excellent, very quick to identify my needs and to fix issues. Very Knowledgeable about Apple and Macintosh products . A very smart and focussed technician . I am very happy with his serviced happy to recommend him to anyone whinnied tech help.

Steve P., Google review

Questions about network cabling

Straight answers. More in our questions and answers.

Still deciding?

Call a Canberra technician, 9 am to 8 pm, 7 days.

Call 1300 224 027
Do you install the cabling yourselves?

We plan the cabling and manage the job, and a registered cabler installs and tests everything fixed in walls, ceilings and floors, as Australian rules require. We then patch, label and configure the network ourselves, so you deal with one contact from start to finish.

Should we use Cat6 or Cat6A?

Cat6 is plenty for desks, printers, phones and cameras. We use Cat6A for ceiling access points, links between cabinets and anything you want to last through several generations of Wi-Fi, because it carries 10 Gb/s to the full 100 metres and copes better with high-power PoE in large bundles.

How many data points does each desk need?

Two is a sensible default: one for the dock or computer and a spare for a phone, a second machine or whatever comes next. Meeting rooms usually need points for the screen and a video bar, and printers, TVs and access points each need their own.

Do we still need cabling if our Wi-Fi is good?

Yes. Every access point needs a cable, and docks, printers, cameras and anything moving large files work better wired. Good cabling is what makes good Wi-Fi possible.

Can our existing cabling be reused?

Often. We test the existing runs, and Cat5e or Cat6 that tests well is usually fine for desks. Runs that fail, copper-clad aluminium cable and anything daisy-chained get replaced.

What is a TCA1 form?

It's the telecommunications cabling advice form a registered cabler gives you after the job, recording the work and confirming it meets the Wiring Rules. Keep it with the test report, because landlords and whoever works on the cabling next will want to see both.

Can you run cable to a shed or another building?

Yes, through a registered cabler with the right endorsements. Between buildings we use fibre in underground conduit rather than copper, because copper between separate buildings can carry surges from lightning and differences in earthing. Where trenching isn't practical, a point-to-point wireless link can bridge the gap.

Will the cabling work disrupt the office?

Most cabling can be done with staff working around it, and noisy or ceiling-heavy work can usually be booked early, late or on a weekend. Switching desks over to the new patching is done after hours, so people come back to a working network.

Book a free IT review

We look at your devices, accounts, backups and security, then give you a plain-English plan and a fixed quote.

1300 224 027

Calls answered 9 am to 8 pm, 7 days.

  • Free and no obligation
  • Written plan and a fixed monthly quote
  • Repairs done in our Mitchell workshop
“Very personable and professional attention to the problem. Would use again.”
Paula K., Google review

Book a free IT review

A 30-minute look at your devices, accounts, backups and security, with a written plan.

IT reviewTB-·····

How many people?
What do you need?

What happens next

  1. We call you back during opening hours to book a time.
  2. About 30 minutes on-site or remotely, with someone who knows your setup.
  3. You get a written summary and, if you want it, a fixed monthly quote.

Open 7 days, 9 am to 8 pm
Prefer to talk? Call 1300 224 027. We only use your details to answer this request.

Open 7 days, 9 am to 8 pm

Call nowBook online