Repairs
Business IT
Starlink
Home
Call 1300 224 027Book a repair

Open 7 days, 9 am to 8 pm

Starlink roof mounts in Canberra for tin, tile and ridgeline roofs

We mount Starlink dishes on corrugated iron, Colorbond, concealed-fix and tiled roofs across Canberra, rural ACT and the nearby NSW region. The mount goes into the purlins or rafters, never the sheeting alone, every hole is sealed and the cable comes inside through a proper entry. TechBox is an independent installer, not Starlink or SpaceX.

“Great friendly service, on time to solve the problem”
Bruce W., Google review
  • Open 7 days, 9 am to 8 pm
  • Quote before work
  • Fixed into purlins or rafters, never fascia or gutters
  • Sky checked from the roof, not the lawn
  • Flashed entries, drip loops and roof-safe sealant
  • Tin, Klip-Lok, tile and low-pitch skillion roofs
  • Independent installer, visits 7 days
A flat white rectangular satellite dish on a short mast on a ridgeline mount on a corrugated iron roof, with a sealed cable entry under the ridge cap and clear blue sky
Roof mount
Confirmed before we start
Turnaround
Usually one visit
Where
Canberra, rural ACT and nearby NSW

Rather we call you?

Leave your number. We call back 9 am to 8 pm, 7 days, to talk through your roof and the cable run.

We only use your number to call you about this.

for most roof and ridge mounts with a clear cable route
1 visit
of cable in the Standard box, which sets how far the router can go
15 m
Starlink's operational wind rating. The mount has to hold it too
96 km/h+
visits, including weekends, with calls until 8 pm
7 days

Roof jobs we take on

  • A new kit and a roof you'd rather not climb

    We get up there, run the obstruction check from the ridge and each likely roof face, and mount the dish where the sky is clearest.

  • Trees that block every spot at gutter height

    A ridge mount or a short mast often lifts the dish clear of the neighbour's oak or the gums along the fence.

  • Tiled roofs on older brick homes

    Concrete and terracotta tiles crack underfoot and around fixings. We fix tile brackets to the rafters, or use a gable wall bracket when that's cleaner.

  • Low-pitch Colorbond and skillion roofs

    Common in Gungahlin and Molonglo. A pivot-style bracket sets the tilt the app asks for, and clamps can avoid holes in concealed-fix sheeting.

  • A dish on a gutter or fascia bracket

    Gutters and fascia boards flex in the wind and rot over time. We move the mount into the roof framing and fill the old holes.

  • A stain on the ceiling near the cable

    Usually a missing drip loop or a hole filled with the wrong sealant. We reseal it with a proper flashing or wall plate.

  • Cable squeezed under a sheet or through a window

    Pinched cables fail. We bring the cable in under the ridge cap, through a flashed roof entry or through the eave lining.

  • Roofs with solar panels

    The dish stays off the solar rails, out of the panels' light and clear of the solar cabling.

  • Two-storey and steep roofs

    Height and pitch change the safety setup. If a gable wall bracket does the same job with less risk, we'll suggest it.

Pick the job. We confirm a fixed price for your exact model before any work starts.

What happens next

  1. Send us photos

    Call 1300 224 027 or use the form. Send photos of each roof face, the trees around the house and where you'd like the router, and tell us the roof type if you know it.

  2. Check the sky from the roof

    We run the Starlink app's obstruction check from each candidate spot on the roof, then agree the position, mount and cable route with you.

  3. Fix, route and seal

    Mount into a purlin or rafter, cable clipped or in conduit with a drip loop, entry flashed or sealed, swarf swept off and tiles checked.

  4. Activate and test

    We activate the kit on your phone with you, test Wi-Fi in the rooms that matter and show you the obstruction map and outage history in the app.

Exploded technical drawing: a starlink install, part by part

What goes up on the roof, and why each bit matters.

  • The dishNeeds a clear view of the sky in every season.Drawn in red: where we focus first
  • Mount and mastRidge, pivot, wall or pole, chosen for the view and the wind.
  • Cable runClipped, protected and given a drip loop.
  • Weatherproof entrySealed where the cable goes into the house.
  • RouterPlaced where the Wi-Fi can reach, or wired to mesh.

Why the roof is usually the right place

On most houses the roof is the highest, clearest surface, right above the rooms you use. The cable to the router stays short, so the router can go somewhere central instead of the garage.

It isn’t automatic. If tall trees stand close on the side of the sky the dish faces, no amount of roof clears them, and a pole set back from the tree line usually works better.

What a proper roof mount includes

Most roof problems we're called out to are fixings, holes and cables, not the dish itself.

  • Fixed into the framing

    Screws go through the crest of the sheet into a purlin or rafter. Never into sheeting alone, fascia or a gutter.

  • Sky checked from the roof

    The app's obstruction check is run from the exact spot, so the result matches what the dish will see.

  • Sealed, not just siliconed

    Flashed or grommeted entries, neutral-cure sealant on metal roofs and a drip loop below every entry.

  • Swarf swept off

    Drilling leaves steel filings that rust and stain Colorbond within days. We clear them before we come down.

  • Solar left alone

    The dish stays off the solar rails, out of the panels' sun and away from the solar cabling.

  • A tidy cable run

    Clipped flat along the ridge and down to the eave, so there's nothing loose for wind or cockatoos to work on.

  • Router where it works

    The cable route is planned so the router sits central and indoors, not wherever the cable happened to end.

  • Your account, your phone

    The Starlink account stays in your name. We activate the kit on your phone with you and never need your password.

Fixing into a metal roof without leaks or rust

A ridge mount lifts the dish above nearby trees, with the cable entering under the ridge cap.
A ridge mount lifts the dish above nearby trees, with the cable entering under the ridge cap.

Most leaks around roof-mounted dishes come from screws in the wrong place or the wrong sealant.

  • Crest, not valley. On corrugated iron and pierce-fixed Colorbond, fixings go through the crest, where water doesn’t run, into a purlin found from the existing screw lines.
  • The right screws. Class 3 or 4 roofing screws with sealing washers, matched to the roof’s coating.
  • Neutral-cure sealant only. Acetic-cure silicone, the kind that smells of vinegar, attacks the coating.
  • Swarf cleared. Makers’ guidance is to clear steel filings at the end of every job, gutters included, because overnight they rust and streak the sheet.
  • Clamps on Klip-Lok. Concealed-fix sheeting moves as it heats and cools, so rib-profile clamp brackets, as solar installers use, often beat screws.

Roof mount problems and what fixes them

Faults on roof-mounted dishes usually come down to the spot, the fixing or the cable. This is what we look for.

What you noticeLikely causeThe fix
What you noticeDrops every few minutes, worse in summerLikely causeLeaves moving into the dish's viewThe fixRidge mount or short mast, or a clearer roof face
What you noticeDish leaning after a strong westerlyLikely causeFixed into sheeting, fascia or a gutterThe fixRefix into a purlin or rafter
What you noticeCeiling stain near the cable entryLikely causeNo drip loop, or a failed sealThe fixAdd a drip loop, flash the entry and reseal
What you noticeOrange rust spots around the mountLikely causeSwarf left behind or mismatched screwsThe fixClean off, refit with matching roofing screws
What you noticeCracked tiles around the dishLikely causeTiles drilled through or walked onThe fixReplace tiles, fit a rafter-fixed tile bracket
What you noticeChewed or flapping cable on the roofLikely causeLoose, unclipped cable runThe fixClip it down or run it in UV-stable conduit
What you noticeRouter can't find the dish after rainLikely causeWater at a plug or a damaged cableThe fixTest the cable and plugs, replace if needed
What you noticeStrong Wi-Fi in the garage onlyLikely causeRouter placed where the cable endedThe fixRe-route the cable, or add mesh

Not sure which one it is? Send us the symptoms and we’ll tell you before you travel.

Tiled roofs on older Canberra homes

Many brick homes in Belconnen, Woden, Weston Creek and Tuggeranong have concrete or terracotta tiles forty or more years old. They crack under a boot, and the ridge mortar can be loose already.

We don’t drill through tiles. Instead:

  1. Lift the tiles. Only at the mounting point.
  2. Fix to the rafter. The bracket screws into the timber underneath.
  3. Notch the tile above. A small ground notch lets it sit flat over the bracket arm.
  4. Refit the course. So it still sheds water, checking the ridge pointing on the way up and down.

Roof mount options compared

The right mount depends on the roof, the trees and how high the dish needs to sit.

Swipe to compare

Pivot bracket on a roof faceRidge mount or short mastGable or high wall bracketTile bracket to a rafter
SuitsMetal roofs, any pitchMetal or tiled ridgesBrick or framed gable wallsConcrete or terracotta tiles
Avoids holes in the roofPartial
Lifts the dish above the rooflinePartial
Easy to reach laterPartialPartial
Main risk if done badlyLeaks at the screwsDisturbed ridge cappingFixings pulling out of claddingCracked or lifted tiles
Relative costLowestMidLowMid

On most metal roofs, a pivot-style bracket on the clearest roof face is the simplest job. A ridge mount earns its place when low trees or a neighbour's roof just clip the view. Tall trees close to the house usually need a pole instead.

Ridgelines, masts and how high is high enough

Cable clipped flat along the ridge and down to the eave, with the ladder footed at the gutter.
Cable clipped flat along the ridge and down to the eave, with the ladder footed at the gutter.

A ridge mount puts the dish at the highest point, and a short mast adds a little more. It’s right when trees are a moderate distance away and only just poke into view.

What decides a tree’s impact is how high it appears from the dish. A 20-metre gum ten metres from the house towers over the ridge, and an extra metre of mast barely helps; the far side of the roof, or a pole further away, often does.

Metal or tile: what changes on your roof

The roof material decides how the mount is fixed and what can go wrong.

Swipe to compare

Corrugated or pierce-fixed metalConcealed-fix metal (Klip-Lok style)Concrete or terracotta tile
How the mount is fixedThrough the crest into the purlinClamps on the ribs, or through the ribBracket screwed to a rafter under the tiles
Can avoid holes in the roofYes, with rib clampsPartial
How it's sealedSealing washers and neutral-cure sealantSame, or nothing to seal with clampsTiles refitted to shed water
Safe to walk on when dryYes, along the purlin linesYes, along the purlin linesPartial: tiles crack underfoot
Watch out forSwarf rust, old screws, valleysLong sheets that expand in heatBrittle tiles, old mortar pointing

Not sure which roof you have? A photo taken from the gutter line is usually enough for us to tell.

Getting the cable inside properly

A dish taken off an old gutter bracket, ready for a pivot mount fixed into the framing.
A dish taken off an old gutter bracket, ready for a pivot mount fixed into the framing.

The cable has to reach the router without being pinched, cooked or chewed. Every entry gets a drip loop below, so water falls off instead of following it inside.

The usual routes

  • Under the ridge cap or barge flashing into the roof space
  • Through a flashed rubber roof boot
  • Down the eave and through the soffit with a grommet
  • A sealed wall plate on a gable wall

In the roof space, the cable stays clear of downlight transformers, mains cabling and hot flues, clipped up away from possums and rats.

Safety, frost and the roofs we steer away from

Canberra winter mornings leave frost and dew on metal roofs that make them treacherous until mid-morning, so roof work waits until they’re dry.

We visit 7 days, so a rescheduled wet or windy day is rarely far off.

Heritage roofs and roofs with failing timber get the same treatment. If a previous install damaged the roof, Starlink relocation covers moving the dish and making good.

Packages

Starting points we tailor to your property. Every package is quoted after a quick look.

Single-storey metal roof

Most homes with a clear roof face and a short cable route to the router

  • Obstruction check from the roof itself
  • Pivot-style or ridge mount fixed into the framing
  • Cable clipped or in UV-stable conduit, with a drip loop
  • Flashed or grommeted entry, swarf swept off
  • Router placed, kit activated and Wi-Fi tested
Get this quoted

Tiled or two-storey home

Older tiled roofs and taller houses where access and fixing take more care

  • Tile bracket fixed to a rafter, or a gable wall bracket
  • Tiles notched and refitted to shed water, not drilled
  • Ridge capping and pointing checked before and after
  • Cable through the eave or a sealed wall plate
  • Router placed, kit activated and Wi-Fi tested
Get this quoted

Roof mount plus whole-home Wi-Fi

Long, brick or multi-wing homes where one router won't reach

  • Everything in the roof install
  • Starlink mesh, or your own mesh with Starlink in bypass mode
  • Ethernet to a home office or TV where the route allows
  • Coverage tested room by room
Get this quoted

What Canberra customers say

Real Google reviews. We ask every customer, every time.

Very personable and professional attention to the problem. Would use again.

Paula K., Google review

The service I have received from TechBox has been nothing but amazing!! I haven’t seen such service for years.I had a problem and asked for their help , from the beginning to the end they were tenacious working through the issues I had with my software. Thank you so much for your help TechBox. You people are most professional I will have no problem…

Steve W., Google review

Very quick. Very efficient. Excellent value for money.

Keith J., Google review

Questions about roof and ridge mounts

Straight answers. More in our questions and answers.

Still deciding?

Call a Canberra technician, 9 am to 8 pm, 7 days.

Call 1300 224 027
Will a roof mount leak?

Not when it's done properly. On metal roofs we fix through the crest of the sheet, where water doesn't run, using roofing screws with sealing washers and a neutral-cure sealant. Every cable entry gets a drip loop and a flashed or grommeted entry. If something isn't right, we come back and make it right.

Can you mount Starlink on a tiled roof?

Yes. We lift the tiles, fix a bracket to the rafter underneath, notch the tile above so it sits flat and refit everything so the roof still sheds water. If the tiles are brittle or the pitch is steep, a gable wall bracket is often the cleaner job, and we'll tell you before we start.

Is the ridge always the best spot?

Often, because it's the highest point of the house. Not always, though: the dish looks at a particular part of the sky, and a lower roof face on the open side can beat a ridge with a gum close by. We run the obstruction check from both before choosing.

Will it work on a low-pitch or skillion roof?

Yes. The dish doesn't sit flat on the roof. A pivot-style bracket holds it at the tilt and direction the app asks for, which suits the low-pitch Colorbond roofs on many newer homes in Gungahlin and Molonglo.

What about our solar panels?

We keep the dish off the solar rails and away from the array, so it doesn't shade the panels or put screws near solar cabling. In Canberra the sun sits to the north, so a dish south of the panels, or on another roof face, usually avoids shading altogether.

How does the cable get inside?

Into the roof space first, then usually down inside a wall cavity to a wall plate beside the router, or through a small ceiling plate in a cupboard. On a two-storey home or a wall we can't get inside, it can run down the outside in a cover strip and through a sealed wall plate. The plug is pushed through whole, never cut off and re-joined, which adds a weak point and may affect your warranty with Starlink.

Can you move my dish off the gutter?

Yes. Gutter and fascia brackets are a common DIY setup we redo. We move the dish onto a mount fixed into the framing, re-run and reseal the cable and fill the old holes.

I rent. Can I still have a roof mount?

Yes, with your landlord's written permission for any holes. A wall bracket or rib clamps keep changes small, and we can note exactly what was fitted so it's easy to remove at the end of the lease.

Do I need to be home for the install?

For activation and testing, yes, or someone with the Starlink app signed in on their phone. We also need access to the roof space and the router spot, and dogs secured while the ladder's up.

Get a mount plan and a fixed quote

Tell us about the property. We plan the mount, the cable run and the Wi-Fi so it works in every room and every season.

1300 224 027

Calls answered 9 am to 8 pm, 7 days.

  • Quote before any work starts
  • Workshop in Mitchell, visits across Canberra
  • If something isn’t right, we come back and make it right.
“Very quick. Very efficient. Excellent value for money.”
Keith J., Google review

Get a Starlink install quote

Tell us about the property. We’ll check the site and quote the mount and cable run.

Starlink quoteTB-·····

Property type
Do you have a kit?

What happens next

  1. We call you back, 9 am to 8 pm, 7 days.
  2. We talk through the roof, trees and cable run, then confirm the mount and a price.
  3. We book the visit. Nothing is ordered until you say yes.

Open 7 days, 9 am to 8 pm
Prefer to talk? Call 1300 224 027. We only use your details to answer this request.

Open 7 days, 9 am to 8 pm

Call nowBook online