Repairs
Business IT
Starlink
Home
Call 1300 224 027Book a repair

Open 7 days, 9 am to 8 pm

Business Wi-Fi and ceiling access points in Canberra, planned from a site survey

Wi-Fi that drops between rooms, crawls in the meeting room or never reaches the back of the warehouse. We survey your building, mount business access points where the signal is actually needed, tune channels and roaming, and keep staff, guests and devices on separate networks, with registered cablers coordinated for anything in the ceiling.

“Great friendly service, on time to solve the problem”
Bruce W., Google review
  • Open 7 days, 9 am to 8 pm
  • Free IT review
  • Site survey before anything is bought
  • Access points placed on your floor plan
  • Roaming tuned so calls survive a walk
  • Guests kept off your staff network
  • Coverage checked room by room at handover
A white circular wireless access point on an office ceiling grid with a single network cable, open-plan desks blurred below
IT review
Free
Turnaround
Survey and design first, install usually after hours
Where
On-site across Canberra and nearby NSW

Talk to us about your IT

Leave your number. We call back during opening hours to book your free IT review, or just to answer questions.

We only use your number to call you about this.

signal we design for at every desk, the usual target for calls
-67 dBm
2.4, 5 and 6 GHz, each given a different job
3 bands
uplink most small-office Wi-Fi 7 access points are built around
2.5 GbE
cut-over, so nobody loses Wi-Fi in the middle of a meeting
After hours

Wi-Fi problems we fix

  • Calls drop between desk and meeting room

    The laptop clings to the access point it started on until the signal is almost gone, then reconnects from scratch.

  • Full bars, slow anyway

    Strong signal but no speed usually means interference from your own or neighbouring access points on the same channel.

  • The meeting room falls over when it's full

    Ten people on a video call need capacity, not just coverage, and one access point in the corridor can't provide it.

  • Dead spots behind brick, concrete and glass

    Double-brick walls, lift cores and coated glass in Canberra offices stop signal that a floor plan suggests should get through.

  • Warehouse and yard blind spots

    Metal racking, high roofs and roller doors leave scanners and tablets dropping out halfway down an aisle.

  • Guests on the staff network

    A visitor's phone can see your printers, file shares and the accounts PC, because there's only one network.

  • One password everyone knows

    The same Wi-Fi key for years, known by former staff, contractors and anyone who read it off the whiteboard.

  • A mesh kit that's run out of road

    Home mesh units on desks and shelves, linked wirelessly, struggling with a growing team and more rooms.

  • Printers and scanners that won't stay connected

    Older devices that don't support newer security or roaming settings and fall off after every change.

What happens next

  1. Survey

    We walk the building with you, measure existing signal and interference, count neighbouring networks and talk through how each space is used.

  2. Design and quote

    Access point positions on your floor plan, mounting, cabling scope, switch and power needs and the networks you'll have, before anything is ordered.

  3. Cable and mount

    A registered cabler runs any new cable. We mount the access points, connect them to the switch and configure them in advance.

  4. Cut over after hours

    The old Wi-Fi is retired and devices are moved across after close of business, so staff arrive to a working network.

  5. Check and hand over

    We measure signal in every room, adjust where needed and hand over documentation with the admin credentials stored securely.

Exploded technical drawing: planning an office network

Planning an office network

Coverage, cabling and the comms cupboard, on paper first.

  • Access pointsPlaced for coverage and roaming, not convenience.
  • Desk cablingInstalled by registered cablers, planned by us.
  • Comms cupboardVentilated, tidy and documented.Drawn in red: where we focus first
  • Meeting roomsScreens and calls that just work.

Why the survey comes before the shopping list

Access points go on the ceiling in open space, where the signal spreads down over the desks, never above the tiles.
Access points go on the ceiling in open space, where the signal spreads down over the desks, never above the tiles.

Most office Wi-Fi problems are baked in the day someone buys the equipment. We measure first: existing signal, interference and how many neighbouring networks compete for the same channels.

We design for capacity as well as coverage: how many staff sit in each area, which rooms host eight-person video calls, and the laptop, phone, watch or tablet each person brings to share the airtime.

Canberra buildings are the hard part

  • Double-brick 1970s and 80s offices, and houses converted to clinics
  • Concrete lift cores and coated glass in Civic, Barton and Woden
  • Floor-to-ceiling metal racking in Mitchell and Fyshwick warehouses
  • Thirty or more neighbouring networks in shared buildings

What a business Wi-Fi install includes

Good Wi-Fi is mostly decided before the first access point goes up: where it's mounted, what it's cabled to and how it's set.

  • A site survey first

    Existing signal, interference and neighbouring networks measured on site, and each room's use talked through with you.

  • Placement on your floor plan

    Every access point marked on the plan, with the reason it's there, before anything is ordered.

  • Power and uplinks sized

    PoE budget and switch port speed checked, so new access points aren't starved of power or bandwidth.

  • Channel and power plan

    Channel widths, channels and transmit power set for your building, not left on automatic defaults.

  • Roaming tuned

    Fast roaming features switched on and tested with your actual laptops, phones and scanners.

  • Guest Wi-Fi kept apart

    Internet only, guests unable to see each other or your devices, with speed limits and a key that changes.

  • Staff sign-in per person

    Individual sign-in or per-device keys where it suits, so leaving staff lose Wi-Fi access with everything else.

  • A network for devices

    Printers, EFTPOS terminals, TVs and sensors on their own network, with rules about what they can reach.

  • Checked and monitored

    Signal measured in every room at handover, then firmware and alerts managed from one dashboard.

Ceiling placement, cabling and power

Each access point gets its own cable run back to the patch panel, installed and tested by a registered cabler.
Each access point gets its own cable run back to the patch panel, installed and tested by a registered cabler.

A ceiling access point radiates down and out like a light fitting, so it belongs in open ceiling space over the people using it, never above the tiles, in a cupboard or beside a metal duct.

  • Its own cable

    Each access point runs back to a switch, limited to about 90 metres from the patch panel, which matters in big warehouses. Long, narrow or high spaces may suit wall mounting or directional antennas.

  • Power over the cable

    Most current access points need PoE+ from the switch, and some Wi-Fi 7 models need the higher-power 802.3bt standard to run every radio.

  • A 2.5 GbE port

    Runs over existing Cat5e or Cat6 at normal office distances. Where new cable is needed, we design the runs and a registered cabler installs them (network cabling).

Why is the Wi-Fi bad?

Most office Wi-Fi complaints come down to a few causes. This is how we tell them apart.

What you noticeLikely causeThe fix
What you noticeDrops walking from desk to meeting roomLikely causeDevice clinging to a distant access pointThe fixTune transmit power, enable 802.11k and v, test roaming
What you noticeFull bars, but slowLikely causeAccess points sharing channels or channels too wideThe fixNarrower channels and a proper channel plan
What you noticeFine early, poor around lunchtimeLikely causeMicrowave or crowding on 2.4 GHzThe fixMove laptops and phones to 5 or 6 GHz
What you noticePrinter won't rejoin after an upgradeLikely causeNo support for WPA3 or fast roamingThe fixA separate device network with settings it understands
What you noticeGuest login page keeps reappearingLikely causePhones rotating private Wi-Fi addressesThe fixVoucher or password access, longer guest sessions
What you noticeNew Wi-Fi 7 access point barely fasterLikely causeOlder laptops, a 1 GbE port or too little PoEThe fixCheck client support, then port speed and power budget
What you noticeScanners drop halfway down an aisleLikely causeMetal racking blocking signalThe fixAccess points down the aisles or directional antennas
What you noticeCalls stutter on Wi-Fi, fine on cableLikely causeToo many networks broadcasting, no traffic priorityThe fixFewer network names, prioritise voice and video

Not sure which one it is? Send us the symptoms and we’ll tell you before you travel.

Channels, bands and transmit power

Out of the box, many access points pick wide channels and full power, which works in a showroom and fails in an office.

Band How we set it Why
2.4 GHz Printers and older devices, switched off on some access points Only three channels don’t overlap: 1, 6 and 11
5 GHz Most traffic, on 20 or 40 MHz channels rather than 80 More channels means less interference; radar channels decided case by case
6 GHz The clean band, WPA3 required Australia opens 5925 to 6425 MHz: 24 channels at 20 MHz, three at 160, one at 320

Wi-Fi 7’s headline 320 MHz width rarely makes sense in a shared building, and older devices won’t see 6 GHz at all.

Wi-Fi generations for a business install

Laptops and phones from the last few years mostly support Wi-Fi 6 or newer. Here's what each generation brings to an office.

Swipe to compare

Wi-Fi 5Wi-Fi 6Wi-Fi 6EOur pickWi-Fi 7
Standard802.11ac802.11ax802.11ax802.11be
Bands5 GHz2.4 and 5 GHz2.4, 5 and 6 GHz2.4, 5 and 6 GHz
Handles crowded rooms well
Uses the clean 6 GHz band
Uses two bands at once (multi-link)
WPA3 security built inPartial
Switch port for full speed1 GbE1 GbE2.5 GbE2.5 GbE or faster
Power over EthernetPoE or PoE+PoE+PoE+PoE+, some need 802.3bt
Worth installing new in 2026Budget refresh only

Older laptops still connect to a Wi-Fi 7 access point, at their own generation's speed. If your switches can't supply 2.5 GbE and PoE+, budget for that too, or Wi-Fi 6E may be the better buy.

Roaming that holds a Teams call

Before: a consumer router and an unmanaged switch on the floor, with no power budget for access points.
Before: a consumer router and an unmanaged switch on the floor, with no power budget for access points.

The device decides when to move to a closer access point, not the network, and many laptops hold on to the first one until the signal is nearly gone.

  • 802.11k. Gives devices a list of nearby access points to move to.
  • 802.11v. Lets the network suggest a better access point.
  • 802.11r. Shortens the reconnection so a call doesn’t drop.

Some older printers, barcode scanners and laptop Wi-Fi drivers refuse to connect with 802.11r on, so we test with your devices and move problem ones to a separate network. Minimum-signal settings push clingy devices off, but set too high they cause disconnect loops.

We keep network names to three or four, because every extra one broadcasts constantly and uses up airtime.

Mesh kit or business access points?

Home mesh is good at what it's designed for. Past a few staff, the differences start to matter.

Swipe to compare

Consumer mesh kitOur pickBusiness, app or controller managedBusiness, cloud licensed
Ceiling mounted, powered over the cable
Wired link to every unitPartial
Separate staff, guest and device networksPartial
Fast roaming (802.11k, v and r)Partial
One dashboard across several sites
No ongoing licence needed
ExamplesEero, Deco, OrbiUniFi, Omada, Aruba Instant OnMeraki, Juniper Mist, Aruba Central
SuitsHomes and 1 to 2 person officesMost offices with 3 to 50 staffMulti-site groups with strict IT policies

If a platform needs an ongoing licence, you'll see the renewal cost alongside the hardware before you decide. For homes, our mesh Wi-Fi installation service is the better fit.

Guest Wi-Fi and staff sign-in

Guests get internet only, can’t see each other or anything of yours, and use a capped connection with a password or voucher that changes on a schedule.

Login pages that recognise devices by address struggle, because iPhones and Android phones use private Wi-Fi addresses, which iOS 18 and later can rotate, so returning guests get asked again. Vouchers or longer sessions work better.

Staff shouldn't share one password former employees still know

  • Certificate sign-in (802.1X). The strongest option, pushed to managed devices through Microsoft Intune or Jamf, with a RADIUS service checking each certificate.
  • A key per person or device. A simpler middle ground than certificates.
  • A device network. Printers, payment terminals and screens apart, with the firewall deciding what each network can reach.

For dropouts in the meantime, our Wi-Fi dropouts guide covers the quick checks.

Packages

Starting points we tailor to your property. Every package is quoted after a quick look.

Open-plan office

One floor of open desks with a few meeting rooms

  • On-site survey and floor plan design
  • Ceiling access points, typically two to four
  • Staff, guest and device networks
  • PoE switch checked or supplied
  • Channel, power and roaming plan
  • Room-by-room check and documentation
Get this quoted

Clinic or multi-room practice

Consult rooms, treatment rooms and offices behind brick or glass walls

  • Room-by-room survey, including through walls
  • More access points at lower power
  • Payment terminals and devices on their own network
  • Patient Wi-Fi with time and speed limits
  • Roaming tested with tablets and phones
  • Documentation for your practice records
Get this quoted

Warehouse, workshop and yard

High roofs, metal racking and outdoor areas, in places like Mitchell, Fyshwick and Hume

  • Survey along aisles, docks and roller doors
  • High-mount or directional access points
  • Outdoor-rated units for yards
  • Scanners and tablets on a device network
  • Roaming tuned for handhelds
  • Cabling scoped with a registered cabler
Get this quoted

Before we survey

Ten minutes of notes makes the survey faster and the design better. None of this needs a ladder.

Stop and call us if: Don't move ceiling access points, lift ceiling tiles or rewire the comms cupboard yourself. Ceiling cabling needs a registered cabler, and moving one access point changes the coverage of every one around it.

What Canberra customers say

Real Google reviews. We ask every customer, every time.

The service I have received from TechBox has been nothing but amazing!! I haven’t seen such service for years.I had a problem and asked for their help , from the beginning to the end they were tenacious working through the issues I had with my software. Thank you so much for your help TechBox. You people are most professional I will have no problem…

Steve W., Google review

Duvi was excellent, very quick to identify my needs and to fix issues. Very Knowledgeable about Apple and Macintosh products . A very smart and focussed technician . I am very happy with his serviced happy to recommend him to anyone whinnied tech help.

Steve P., Google review

Very quick. Very efficient. Excellent value for money.

Keith J., Google review

Questions about business Wi-Fi

Straight answers. More in our questions and answers.

Still deciding?

Call a Canberra technician, 9 am to 8 pm, 7 days.

Call 1300 224 027
How many access points do we need?

It depends on the building and how many people work in each space, which is why the survey comes first. Two well-placed access points can cover an open-plan floor, while a clinic with brick consult rooms may need one every few rooms. We design for the fewest that give strong signal and enough capacity everywhere.

Can't we just add another mesh node?

For a home or a two-person office, often yes. Past that, wireless links between mesh units lose speed with every hop, and most mesh kits can't run separate staff, guest and device networks properly. Business access points are each cabled to a switch, so every one gets full bandwidth.

Do access points need a power point in the ceiling?

No. They're powered through the network cable using Power over Ethernet from the switch in your comms cupboard. That also means a UPS on the switch keeps Wi-Fi running through a short power blip.

Should we buy Wi-Fi 7 now?

For a new install in 2026, usually yes, as long as your switches can deliver 2.5 GbE and PoE+ to each access point. If they can't and the budget is tight, Wi-Fi 6E on your existing switches can be the better value. We'll show you both.

Why does my call drop when I walk to the meeting room?

Your laptop, not the access point, decides when to switch, and many hold on too long. We set transmit power so cells overlap properly and switch on the roaming features that help devices move early, then test with your actual devices.

Can guests get to our files or printers?

Not on a network we set up. Guest Wi-Fi sits on its own network with internet access only, guests can't see each other, and speed is capped so a visitor's download doesn't slow your calls.

Can staff sign in to Wi-Fi with their work account?

Yes. The most secure option is certificate-based sign-in pushed to managed laptops and phones through Intune or Jamf, which needs a sign-in service behind it because Microsoft Entra ID doesn't provide one for Wi-Fi on its own. Many platforms also support a separate key per person or per device, which is simpler and still lets you cut off one person without changing everyone's password.

Can you reuse our existing access points or cabling?

Often. If your access points still get firmware updates, we can survey and retune them first, which sometimes fixes the problem outright. Existing Cat5e or Cat6 cabling usually supports 2.5 GbE over normal office distances, which saves pulling new cable.

Who installs the cabling?

Fixed cabling in Australia has to be installed by a registered cabler. We design the runs and coordinate a registered cabler to install and test them, then mount and configure the access points ourselves.

Book a free IT review

We look at your devices, accounts, backups and security, then give you a plain-English plan and a fixed quote.

1300 224 027

Calls answered 9 am to 8 pm, 7 days.

  • Free and no obligation
  • Written plan and a fixed monthly quote
  • Repairs done in our Mitchell workshop
“Very personable and professional attention to the problem. Would use again.”
Paula K., Google review

Book a free IT review

A 30-minute look at your devices, accounts, backups and security, with a written plan.

IT reviewTB-·····

How many people?
What do you need?

What happens next

  1. We call you back during opening hours to book a time.
  2. About 30 minutes on-site or remotely, with someone who knows your setup.
  3. You get a written summary and, if you want it, a fixed monthly quote.

Open 7 days, 9 am to 8 pm
Prefer to talk? Call 1300 224 027. We only use your details to answer this request.

Open 7 days, 9 am to 8 pm

Call nowBook online