Starlink Wi-Fi to every room, the home office and the shed
The dish is working, but the Wi-Fi stops at the kitchen. We carry your Starlink connection to the far bedrooms, the home office, the shed and the cottage down the track, using Starlink mesh, your own mesh system, cable or a point-to-point wireless link. TechBox is an independent installer, not Starlink or SpaceX.
Call 1300 224 027 or use the form. List the rooms and buildings that need internet, and send a rough sketch or an online map screenshot of the property.
Test and plan
We check the Starlink connection first, then measure signal room by room and the line of sight to any outbuildings. You get a plan and a fixed quote before work starts.
Install and connect
Nodes, access points and links go in, cable runs are arranged, and separate networks are set up for guests, workers and cameras.
Test again and hand over
We repeat the tests in every room and building, show you the results, and leave a simple map of what's where.
Planning a rural property
Internet that reaches the house, the office and the shed.
Dish locationPicked after an obstruction check through the seasons.Drawn in red: where we focus first
House Wi-FiMesh nodes for brick walls and long homes.
Link to the shedA point-to-point link or buried cable for outbuildings.
Backup powerA small UPS keeps the internet up through short outages.
Why one Starlink router rarely covers a rural home
Starlink’s spec sheet figures are best cases. Brick walls, foil sarking, steel framing and the router’s position all cut into them, so the far bedrooms end up on one bar.
The Gen 3 router
Rated up to 297 square metres in the Standard kit. A homestead with double-brick internal walls, foil sarking and a steel-framed extension behaves very differently.
Where the router sits
Wherever the dish cable reaches, often the laundry, garage or a front room near the eaves. A router in the corner gives great coverage in the paddock next to it.
The Mini
Its Wi-Fi comes from the dish outside, rated up to 112 square metres, and every wall eats into that. At a permanent home, plan a wired router or mesh inside.
What a whole-property Starlink network includes
More nodes don't fix bad Wi-Fi on their own. Where they go, and how they connect back to the router, matters more than how many there are.
Nodes placed by testing
We measure signal and speed in each room before fixing node positions, rather than guessing from a floor plan.
Wired backhaul where practical
A cable between the router and a node beats a wireless hop every time, so we use one wherever a run is possible.
Building-to-building links
Point-to-point radios or buried cable to sheds and cottages, with an access point inside each building.
Separate networks
Guests, workers and a farm-stay cottage get internet without seeing your office computers or cameras.
Cameras and sensors included
Gate cameras, tank sensors and weather stations are planned into the same network, not bolted on later.
Power and surge planning
A UPS for the router and key nodes, and fibre or radio between buildings so a surge can't travel down a cable.
A map of what's where
A simple diagram of the router, nodes, links and network names, so anyone can find them later.
Check the sky before the Wi-Fi
A node in the machinery shed office, fed by a link from the house rather than Wi-Fi through the steel walls.
Before adding hardware, we work out whether the problem really is Wi-Fi. If Starlink itself is slow or dropping, more mesh nodes won’t help.
Test by cable. A laptop plugged straight into the router shows what Starlink is delivering.
Read the app. Short freezes every few minutes, on every device in every room, usually mean a branch or roofline in the dish’s view, shown in the outage history and obstruction map.
Measure each room. Signal strength and speed in every room you use, so each node position is measured, not guessed.
Why the Wi-Fi doesn't reach
What you notice usually points to the cause. Here's how we read it on site.
What you noticeLikely causeThe fix
What you noticeStrong in the kitchen, dead in the far bedroomLikely causeBrick internal walls or foil insulation in betweenThe fixA node at the halfway point, or a wired node
What you noticeFull bars on the phone but slow, laggy callsLikely causeNode too far from the router, weak wireless backhaulThe fixMove the node closer or run a cable to it
What you noticeNothing in a steel shed 40 metres awayLikely causeMetal cladding blocks Wi-Fi almost entirelyThe fixCable or radio link to an access point inside
What you noticeSmart TV buffers, phones beside it are fineLikely causeWeak Wi-Fi in the TV, hidden behind a cabinetThe fixEthernet to the TV, or a node beside it
What you noticeYour own mesh won't pair with StarlinkLikely causeStarlink routers only mesh with other Starlink routersThe fixStarlink in bypass mode, your mesh runs the network
What you noticeEverything freezes for a few seconds, every few minutesLikely causeUsually a sky obstruction, not the Wi-FiThe fixCheck the app's obstruction map before adding nodes
What you noticeSlow every evening, fine in the morningLikely causePeak-hour demand on Starlink, or an overloaded older routerThe fixTest by cable at the router to tell which
What you noticeLaptop by the router is fast, phones elsewhere aren'tLikely causeCoverage gap, not the Starlink connectionThe fixA node or wired access point where the speed drops
Not sure which one it is? Send us the symptoms and we’ll tell you before you travel.
Mesh inside the house
Starlink’s own mesh is the simplest: extra Starlink routers pair in the app and extend the same network name. Bigger jobs put your own system in charge.
Option
When it suits
Starlink mesh
Most single-building homes, with one or two nodes
Your own system, Starlink in bypass mode
Larger homes, ceiling access points, detailed guest controls, or Wi-Fi 6E and 7
The Gen 3 router has two Ethernet ports for your own router; older Standard Actuated kits need Starlink’s Ethernet adapter.
Most properties end up with a mix: mesh inside the house, cable where it's practical and a radio link for the building that's too far away.
Swipe to compare
Starlink mesh
Your own mesh (bypass)
Our pickEthernet cable
Point-to-point link
Typical reach
Most single-storey homes
Large or multi-level homes
Up to 100 m per run
Hundreds of metres to kilometres
Unaffected by brick walls and foil
Partial
Partial
Reaches a separate steel shed
Full speed at the far end
Partial
Partial
Works without a clear line of sight
Partial
Partial
Simple to set up
Partial
Partial
What slows it down
Each wireless hop
Wireless backhaul
Nothing within 100 m
Trees or a rise midway
Hardware cost
Low
Low to high
Low parts, more labour
Mid, plus mounting
Best for
Compact homes
Big homes, more control
Offices, TVs, mesh nodes
Sheds, cottages, cellar doors
We use cable wherever a run is practical and wireless only where cable isn't. A wired node or access point is the most reliable way to extend any network.
Getting to the shed, studio or cottage
A node placed where testing showed it could reach both the router and the far bedrooms.
Separate buildings are where most rural networks fall down, because steel cladding stops Wi-Fi almost completely. The options depend on distance.
Close, with a clear path. A mesh node in a window facing the house can sometimes bridge 20 or 30 metres to a timber studio or granny flat, rarely into a steel shed.
Up to 100 metres. Buried cable in white communications conduit, apart from power, with an access point inside. A registered cabler installs it; we plan the route and set up both ends.
Further, or across a paddock. Point-to-point radios on each eave. 5 GHz units such as Ubiquiti NanoBeam or TP-Link CPE suit a few hundred metres to several kilometres.
Short, fast hops. 60 GHz radios are faster but more affected by heavy rain.
Starlink's router or your own mesh?
Both work well. The choice comes down to how big the property is and how much control you want.
Swipe to compare
Gen 3 router and Starlink mesh
Bypass mode and your own system
Managed from
The Starlink app
Your system's own app
Extra nodes
Other Starlink routers only
Any node from the same system
Wi-Fi generation
Wi-Fi 6
Wi-Fi 6, 6E or 7, your choice
Wired ports
Two on the router
Usually several, plus switches
Ceiling-mounted access points
Weatherproof outdoor access points
Yes, on most systems
Detailed guest, IoT and parental controls
Partial
One app for dish and Wi-Fi
No, two apps
Suits
Most single-building homes
Big homes, several buildings, lots of devices
Older Standard Actuated kits use a router with no Ethernet port, so a wired node or your own router needs Starlink's Ethernet adapter. The Gen 3 router has two ports built in.
Home offices and work devices
Video calls are the hardest test, needing steady upload as well as download, and a freeze is obvious to everyone on the call.
A cable to the desk wherever we can, or a node in the same room
A UPS so a short blackout doesn’t end the meeting
Work laptops on their own network, apart from tablets, TVs and cameras
Your office VPN tested on Starlink early
Starlink generally sits behind carrier-grade NAT, which is fine for an outgoing VPN but stops you reaching home devices from outside without a different approach.
Router up high and in the open. A cupboard or the floor costs you a room's worth of coverage.
In a blackout the whole network goes down with the Starlink router. A small UPS on the router and home office node covers short outages; for longer ones, see Starlink as backup internet.
When we finish, you get a simple map of the router, nodes, links and network names. To understand the hardware first, start with our mesh Wi-Fi guide.
Packages
Starting points we tailor to your property. Every package is quoted after a quick look.
Whole house
Long, brick or two-storey homes where the far rooms drop out
Real Google reviews. We ask every customer, every time.
Great friendly service, on time to solve the problem
Bruce W., Google review
Duvi came out to fix my computer today and I'm so very happy to say that it is now working again! I'm so grateful as Duvi saved me thousands of dollars because a major electronics chain told me i needed a new computer.
Maree W., Google review
Prompt, professional, and very helpful. Highly recommend.
Yes, with Starlink in bypass mode. Starlink routers only mesh with other Starlink routers, so instead the Starlink Wi-Fi is turned off in the app and your mesh system's main unit plugs into one of the Gen 3 router's Ethernet ports and runs the network. On older Standard Actuated kits, that connection needs Starlink's Ethernet adapter.
How many Starlink mesh nodes do I need?
Most single-building homes need one or two. Every wireless hop adds delay and cuts the speed passed on, so Starlink mesh works best with a few nodes, each within a wall or two of the last. If a property needs more than that, wired access points or your own mesh system in bypass mode usually do the job better and give you more control.
Why not just plug a Wi-Fi extender into the hallway?
A basic extender repeats the signal on the same radio, which roughly halves the speed it passes on, and it often creates a second network name that phones cling to. A mesh node with good backhaul, or a cabled access point, gives you one network that hands devices over properly as you move.
How far can a wireless link reach between buildings?
With a clear line of sight, a pair of 5 GHz point-to-point radios can carry a fast link from a few hundred metres to several kilometres. Trees, a hay shed or a rise in the ground midway along the path weaken it, so we check the view from both ends before quoting.
Can you run network cable to the shed?
We plan the route and the network, and fixed cabling in walls, ceilings and underground is installed by a registered cabler, as Australian cabling rules require. A single copper run is limited to 100 metres. Beyond that, or where lightning is a concern, fibre is the better choice.
Will extending the Wi-Fi make Starlink faster?
No. It carries the speed Starlink already delivers to more places. If the connection drops for a few seconds every few minutes, that's usually something in the dish's view, so we check the app's obstruction map and outage history before recommending any Wi-Fi hardware.
Do mesh nodes and access points need power?
Yes. Every node needs a power point, and ceiling or outdoor access points are usually powered over the network cable from a PoE switch. In sheds we check there's a suitable power point near where the equipment will go.
Can the cottage or workers have Wi-Fi without seeing my computers?
Yes. We set up a separate guest or worker network so they get internet but can't reach your office computers, printers or cameras. If guests stream a lot of video, check that your Starlink plan suits that level of use.