Fixing Wi-Fi dead zones in Canberra homes
Double brick, split levels, the extension out the back and the granny flat down the yard: the usual Canberra Wi-Fi blackspots, why each one happens and the fix that works for it.
26 June 2026. 4 minute read.

In a lot of Canberra homes, the Wi-Fi is great beside the router and fades from there. The study is patchy, the back room drops video calls and the granny flat might as well be in Yass. Usually it’s the house, not the plan.
First, check it's the Wi-Fi
Before you buy anything, work out whether the problem is your connection or your Wi-Fi. Two speed tests will tell you.
- Test at the router. Stand next to it or, better, use a computer plugged into it with a cable.
- Test in the problem room. Run the same test where the Wi-Fi drops out.
- Compare. Slow everywhere means your connection or plan. Slow only away from the router means the Wi-Fi.
If it's the connection
Why Canberra houses are hard on Wi-Fi
Brick, floor slabs, foil and distance all weaken the signal. Most Canberra blackspots come down to one of these.
Brick walls
Older homes in established suburbs often have solid brick internal walls, and some are double brick throughout. Brick and concrete absorb signal, especially when the mortar holds moisture. Brick veneer is easier inside, but the outer skin still blocks signal to the garden and deck.
Split levels
Common in older hillside suburbs, split levels put a floor slab and half a flight of stairs between rooms. Signal crossing a floor at a shallow angle travels through far more material.
The back room
Extensions turn the old external back wall into an internal one, so the new family room sits behind full brick. Foil insulation and energy-efficient glass, common in renovations, make it harder still.
Foil and low-E glass
Reflective foil insulation and low-emissivity (low-E) double glazing are great through a Canberra winter, and both reflect radio signals. They can weaken mobile reception indoors too.
The granny flat
A separate building down the yard means at least two external walls, plus distance. A router inside the house is rarely enough on its own.
Want us to just sort it?
Leave your number. A technician calls back 9 am to 8 pm, 7 days, with a price range for your model.
Move the router first
The router is often in the worst spot in the house. Get it central, off the floor and in the open.
In many Canberra homes the NBN box is in the garage or a hall cupboard, with the router beside it: behind brick, at floor level, in a corner. A network cable can carry the connection somewhere better.
A bigger router helps only a little. Wi-Fi is a two-way conversation, and your phone’s tiny antenna doesn’t get any stronger, so placement and more access points beat raw power every time.
Mesh Wi-Fi, placed properly
A mesh system is several nodes working as one network, with one name and password, and your devices move between them. Placement is the secret.
Each node needs a good signal from the one before it, so put nodes partway towards the dead zone, not inside it. A node in a dead zone has nothing to pass on.
Tri-band
A dedicated radio carries the links between nodes, which keeps speeds up as the signal passes from node to node.
Dual-band
Cheaper systems share airtime between your devices and the node-to-node link, so speed drops at each hop.
Wired backhaul and granny flats
For a brick house, the most reliable fix is to connect the nodes with network cable, called wired backhaul. Each node then gets full speed, however thick the walls.
Newer homes often have data points already, and older homes usually have a path through the roof space or under the floor. Powerline adapters, which use your power wiring, are worth trying where cabling isn’t practical, but results vary a lot.
For a granny flat, most to least reliable
- Cable in underground conduit. Ideally laid when the flat is built or while other trenching is happening.
- Point-to-point wireless bridge. Two small outdoor antennas aimed at each other, house to flat, with a mesh node inside.
- Outdoor mesh node. Mounted on the house, facing the flat.
A repeater balanced on a windowsill is not on the list.
Settings worth checking
A few settings decide whether you end up with one solid network or two competing ones.
- One network, not two. Set your provider’s router to bridge mode or switch off its Wi-Fi when you add mesh.
- Current firmware. Check every mesh node is up to date.
- Automatic channel selection. Usually fine in a house. In townhouses and apartments, a crowded 2.4 GHz band may need a manual channel.
- Smart devices. Many only use 2.4 GHz, so make sure that band reaches the doorbell, garage and backyard camera.
We survey homes across Canberra, place nodes where they’ll actually work, and recommend wired backhaul or a bridge where the building needs one.
Get it booked in today
Call now, or send a ticket and we’ll call you back with a time and a price range. Drop it at Mitchell or we come to you.
1300 224 027Calls answered 9 am to 8 pm, 7 days.
- Quote before any work starts
- Workshop in Mitchell, visits across Canberra
- If something isn’t right, we come back and make it right.
“Great friendly service, on time to solve the problem”





