Repairs
Business IT
Starlink
Home
Call 1300 224 027Book a repair

Open 7 days, 9 am to 8 pm

How to fix

How to fix a laptop that won't charge: Windows laptops and MacBooks

Most laptops that won't charge have a simple cause: a switched-off socket, a worn cable, an underpowered USB-C charger or a charge limit doing its job. Work through these checks in order, from the wall socket to the battery report, and you'll either fix it or know exactly which part has failed.

  • Moderate
  • 10 to 30 minutes
  • 5 min read

Rather we fix it? Same day for many charger and battery faults at our Mitchell workshop, with a fixed quote first.

Open 7 days, 9 am to 8 pm
“Prompt, professional, and very helpful. Highly recommend.”
CHRISTINE F., Google review
A laptop charger brick, two different charging cables and a power board on a desk beside a laptop with its charging light off

Key takeaways

  • Check for a bulging case, a stiff trackpad or a scorched charger first. Any of those means stop, not troubleshoot.
  • Start at the wall: a switched-off socket, a failed power board or a loose mains lead catches plenty of people out.
  • 'Plugged in, not charging' at 60 or 80 per cent is often a battery-care setting, not a fault.
  • USB-C laptops need the right watts and the right cable. A phone charger or a 60 W cable can hold a bigger laptop back.
What you’ll need: A wall socket you know works, A known-good charger of the same type and wattage, A torch, A wooden toothpick.

Rather we just fix it?

Charging fixed: charger, port, circuit and battery tested one at a time, so you only pay for the failed part.

Laptop not charging1300 224 027

Try these fixes, in order

Start at the top. Most problems are solved in the first few steps. Tick them off as you go.

Stop and call us if: none of these work, the fault is probably hardware. Our laptop not charging service picks up where this guide stops.

What your laptop is telling you

Match what you see to the likely cause before you spend anything.

What you noticeLikely causeThe fix
What you noticeNo light on the charger or laptopLikely causeDead charger, loose mains lead or a switched-off socketThe fixReseat, try another socket, then a known-good charger
What you noticeLight flickers when you move the plugLikely causeCracked DC jack or a worn USB-C portThe fixPort or jack repair
What you notice'Plugged in, not charging' at 60 or 80%Likely causeA battery-care charge limitThe fixTurn the limit off in the maker's app or BIOS
What you noticeCharges while asleep, drains while workingLikely causeUnderpowered charger, cable or dockThe fixOriginal-wattage charger, plugged in directly
What you noticeStuck at 0 or 1 per centLikely causeDeeply flat battery locked out, or a failed batteryThe fixBattery test, usually a replacement
What you noticeDead, even on a known-good chargerLikely causeCharging circuit, board fault or battery lockoutThe fixBench test and a fixed quote
What you noticeStopped charging after a spillLikely causeCorrosion on the charging circuitThe fixUnplug, don't test it, bring it in
What you noticeTrackpad stiff, case bulging or rockingLikely causeSwollen batteryThe fixStop charging and bring it in promptly

Not sure which one it is? Send us the symptoms and we’ll tell you before you travel.

Tried these and still stuck?

Leave your number. A technician calls back 9 am to 8 pm, 7 days, and tells you whether it’s worth bringing in before you travel.

We only use your number to call you about this.

What the repair looks like

Drag the handle to compare. This kind of fault, before and after on the bench.

After: charging port, clearedBeforeAfter
Charging port, cleared Packed lint out, contacts clean, charging again.
the most an ordinary 3 A USB-C cable can carry
60 W
the top of USB Power Delivery, with a cable built for it
240 W
below this, lithium-ion batteries shouldn't be charged
0°C
a common charge-limit setting that looks like a fault
80%
Exploded technical drawing: what’s really in your charging port

What’s really in your charging port

Most “broken” ports are full of lint.

  • Packed lintStops the plug seating. Cleaned out safely, no metal tools.Drawn in red: the part we replace most
  • Contact pinsBent or corroded pins mean a new port.
  • Charging chipIf the port is fine, the fault is on the board.

Why a laptop stops charging

Charging is a chain: wall socket, mains lead, power brick, cable, the laptop’s port, a charging controller on the motherboard and the battery.

The fixes on this page test the cheap outside end first, because that’s where faults are most likely.

  • The charger

    Chargers live in bags, get stood on and get wrapped tightly around the brick, which breaks the fine wires inside right where the cable meets the plug.

  • The port

    It takes sideways force every time the plug is knocked or the laptop is used on the couch. That cracks the solder joints on a barrel jack or bends the pins in a USB-C port.

  • The battery and charging circuit

    The battery ages with every charge cycle. A laptop that runs perfectly on the charger but won’t hold a charge almost always has a battery or charging-circuit problem, not a charger problem.

Barrel, USB-C and MagSafe charging compared

The three ways laptops take power fail in different places. Knowing which you have narrows the search.

Swipe to compare

Barrel plug (DC jack)USB-CMagSafe 3
Found onOlder, budget and gaming laptopsMost thin and business laptops, all recent MacBooksMacBook Air from M2, MacBook Pro 14 and 16 from 2021
How power is agreedFixed voltage; ID pin on many Dell and HPNegotiated, 5 to 48 VNegotiated by the USB-C adapter
Can borrow another brand's chargerNo, voltage and plug must matchYes, at similar or higher wattsYes, any good USB-C PD charger
Usual wear pointJack solder joints, bent centre pinLint, worn port, power controller chipFrayed cable near the connector
Backup if the port failsNoneAnother USB-C port, on most modelsAny USB-C or Thunderbolt port
Typical repairQuick on a cable; longer if solderedQuick on a daughterboard; board work if solderedUsually a new cable

A barrel charger that fits isn't necessarily safe: same-size plugs come in different voltages. Always match the label.

USB-C power, without the jargon

After a charging repair, the laptop goes on the test bench so charging is checked under load, not just at idle.
After a charging repair, the laptop goes on the test bench so charging is checked under load, not just at idle.

USB-C laptops use USB Power Delivery: charger and laptop agree on a voltage from 5 to 48 volts and on how much current the cable can carry.

That conversation is where most USB-C trouble starts.

  • Watts decide whether it charges under load. A 65 W laptop on a 30 W charger may charge while asleep and drain while you work, sometimes with a slow-charger warning.
  • The cable sets a ceiling. An ordinary cable carries 3 amps, capping it at 60 W. Above that needs a chipped 5 A cable; 140 W and 240 W need higher-voltage cables.
  • Docks and monitors share their power. A USB-C monitor that supplies 65 W can’t keep up with a powerful laptop running hard.

A cheap inline USB-C power meter shows the voltage and current being negotiated. A laptop stuck at 5 volts on a 20-volt charger means they aren’t agreeing, which points to the cable, the port or the laptop’s power controller chip.

Charger, port, battery or charging circuit?

Four possible faults behind the same complaint. These clues separate them.

Swipe to compare

Charger or cablePort or DC jackBatteryCharging circuit
Typical signWorks fine with another chargerFlickers when the plug movesRuns on the charger, won't hold chargeDead even with a good charger
Known-good charger fixes it
Runs while plugged inOnly with a working chargerOnly at an angleOften not
DIY fix possibleYes, buy a matched chargerPartial: lint onlyNo, it's a workshop job
Usual next stepReplace the chargerPort or jack repairBattery replacementBoard-level quote
Relative costLowestMidMidVaries, quoted first

We test all four separately on the bench, so you only pay to fix the one that failed.

When the battery is the problem

Lithium-ion batteries lose capacity with every cycle. Apple designs recent MacBook batteries to keep up to 80 per cent of original capacity at 1,000 cycles; Windows laptops vary by maker and model.

Once full charge capacity falls well under design capacity, charging gets strange: percentages that stick, sudden shutdowns at 20 per cent, or charging that stops short of full. A battery left flat for months can drop below the voltage its protection circuit accepts, and then won’t charge at all.

  • Cold

    Lithium cells shouldn’t charge below about 0°C, so a laptop left in the car on a frosty Canberra night may refuse until it warms up.

  • Heat

    A laptop left on a car seat in January can be too hot to charge, and heat ages batteries faster than anything else.

What not to do

A worn USB-C port soldered to the board is lifted off with hot air and a new one fitted in its place.
A worn USB-C port soldered to the board is lifted off with hot air and a new one fitted in its place.

Some quick fixes damage the charging circuit or create a fire risk. Skip these.

  • Don’t open the charger brick or the battery. Bricks hold mains voltage and capacitors that stay charged after unplugging, and battery packs aren’t user-serviceable.
  • Don’t tape up a damaged cable. A frayed or scorched lead is a fire risk, so replace the charger.
  • Don’t use a charger just because the plug fits. Same-size barrel plugs come in different voltages, and the wrong one can damage the charging circuit.
  • Don’t buy the cheapest replacement online. No-name USB-C chargers and cables are a common cause of damaged power controllers.
  • Don’t keep plugging in after a spill. Power speeds up corrosion on the board, so switch it off and read our water damage repair page.
  • Don’t press on a lifting trackpad or keyboard. That’s a swollen battery, and pressure can puncture it.

When to bring it in

If the fixes didn’t solve it, a bench test tells us whether it’s the charger, the port, the charging circuit or the battery.

We test each part on its own, so if the charger is the only problem, that’s all you replace.

  1. Bring everything. The laptop, its charger and any other charger you’ve tried.
  2. Describe the light. Tell us what the charging light does when you plug in.
  3. Get a fixed quote. You’ll have it before any work starts.
  4. Often same day. Many charger and battery faults are sorted the same day at our Mitchell workshop.

Your files, and repair or replace

If the laptop won’t turn on at all, your files are usually still safe on the drive. On recent MacBooks and many thin Windows laptops the storage is soldered to the board, so the board has to work to reach them.

That’s one more reason not to leave a charging fault until the battery runs flat for good. If the laptop is old, the battery tired and the port worn, the repairs add up, so weigh the whole machine before you spend.

Common questions

Still stuck? Call 1300 224 027, 9 am to 8 pm, 7 days.

Is it safe to keep using my laptop on the charger if the battery won't charge?

Usually, as long as the battery isn't swollen and the charger isn't damaged. The laptop will run from the charger, but it shuts off instantly if the plug is knocked out, so save your work often. If the case is bulging or the trackpad has gone stiff, stop using it and bring it in.

Why does Windows say plugged in, not charging?

Either the laptop has decided not to charge, or it can't. A battery-care setting that stops at 60 or 80 per cent is the harmless reason. Otherwise it's usually an underpowered charger, a worn battery or a fault in the charging circuit, and a known-good charger plus a battery report narrows it down quickly.

Can I use a more powerful USB-C charger than the one that came with my laptop?

Yes. With USB Power Delivery the laptop only draws what it needs, so a 100 W charger is fine on a 65 W laptop. The reverse is the problem: a weaker charger may charge slowly or let the battery drain while you work. Barrel-plug chargers are different, because the voltage has to match the label exactly.

Can I charge my laptop from my USB-C monitor or dock?

Often, yes. Many monitors and docks supply 65 to 90 W over the same cable as the picture, which is plenty for most thin laptops. A gaming or workstation laptop can still drain under load. If charging stops when you dock, test with the laptop's own charger plugged straight in.

How do I know if my laptop battery is worn out?

Run powercfg /batteryreport on Windows and compare the design capacity with the full charge capacity, or check Battery Health in System Settings on a Mac. Below about 80 per cent, most people notice shorter battery life and odd charging behaviour becomes more common. A Mac that says service is recommended needs a new battery.

My laptop won't charge after a spill. What should I do?

Unplug it, switch it off and don't try charging it again to test it. Liquid plus power is what corrodes the charging circuit. Turn it upside down to drain, then bring it in as soon as you can, because corrosion keeps spreading after the outside looks dry.

Can you look at a charging problem on-site?

We can test the charger, settings and battery on a home or business visit, which is $189 for the first hour, then billed in 30-minute blocks. Port, battery and board repairs are done at our Mitchell workshop, where the parts and test gear are, and many are finished the same day.

Reviews from TechBox customers

Real Google reviews.

The service I have received from TechBox has been nothing but amazing!! I haven’t seen such service for years.I had a problem and asked for their help , from the beginning to the end they were tenacious working through the issues I had with my software. Thank you so much for your help TechBox. You people are most professional I will have no problem…

Steve W., Google review

Very quick. Very efficient. Excellent value for money.

Keith J., Google review

Great friendly service, on time to solve the problem

Bruce W., Google review

Still not fixed? We’ll take it from here

Call now, or send a ticket and we’ll call you back with a time and a price range. Drop it at Mitchell or we come to you.

1300 224 027

Calls answered 9 am to 8 pm, 7 days.

  • Quote before any work starts
  • Workshop in Mitchell, visits across Canberra
  • If something isn’t right, we come back and make it right.
“Great friendly service, on time to solve the problem”
Bruce W., Google review

Start a repair ticket

Tell us what’s wrong. We’ll call you back with a time and a price range.

Repair ticketTB-·····

What needs fixing?

What happens next

  1. A technician calls you back, 9 am to 8 pm, 7 days. Sent after 8 pm? We call from 9 am.
  2. You get a price range and a time for your model.
  3. Nothing starts until you say yes.

Open 7 days, 9 am to 8 pm
Prefer to talk? Call 1300 224 027. We only use your details to answer this request.

Open 7 days, 9 am to 8 pm

Call nowBook online